Manual Whirlpool akm 702 (page 2 of 2) (English)

333515

Zoom out

Zoom in

1/2

AFTER SALES SERVICE

Before you call the After Sales Service

• Make sure that you cannot solve the problem yourself

following the points described in chapter

“Troubleshooting Guide“.

If after the above checks the fault still occurs, get in

touch with the nearest After Sales Service.

Please give:

• a short description of the fault;

• the exact type and model of hob;

• service number (i.e., the number that follows the word

SERVICE on the rating plate under the hob itself). The

service number is also indicated on the guarantee

booklet;

•your full address;

• your telephone number.

If any repairs are required, please contact an authorised

After Sales Service (to guarantee that original spare parts

will be used and repairs carried out correctly).

Failure to comply with these instructions may

compromise the safety and quality of the product.

INSTALLATION

Recommendations

Important: Disconnect the hob from the mains before

carrying out any installation work or servicing.

• All electrical connections must be made before

connecting the appliance to the power supply.

• Installation must be carried out by a qualified technician

in accordance with the manufacturer's instructions and

in compliance with local regulations.

• Unpack the hob and make sure that the appliance has

not been damaged during transport. If you are not

sure contact the dealer or the nearest service

centre.

Preparing the housing unit

• Cut the worktop to fit before installing the appliance.

Carefully remove any shavings or sawdust that could

prevent the appliance from running properly.

Attention: to install the hob on other surfaces than wood

(marble, plastic, ceramic, marble, stone, etc.) remember to

ask After Sales Service for the fixing plates (fig. 2)

Code 4819 404 78697.

• The hob must be fitted in a worktop with a minimum

thickness of 20 mm and a maximum of 50 mm.

• Insert a separator panel at a minimum distance of

90 mm from the bottom of the hob, so that it cannot be

accessed by the user.

• If there is an oven under the hob, make sure that it is

manufactured by us and equipped with a cooling

system.

• There must be nothing between the hob and the oven

(e.g. cables, insulating material, etc.).

• An adjacent column unit must be installed at least

100 mm from the edge of the hob.

• Cut an opening in the worktop of the given dimensions.

• We recommend you seal the internal edges of the

worktop with wood glue or silicone.

• If not already in place, apply the supplied seal to the

hob, after cleaning the adhesive surface thoroughly.

Glass-ceramic hob

Important: remove any protective film before installing

the hob.

Make sure that that the opening in the worktop for the hob is

cut according to the dimensions given in the drawing, paying

attention to the tolerance range.

The hob should not be forced into the worktop. Forcing the

glass-ceramic top may cause it to crack (even at a later date)!

• If the worktop is made of wood, use the spring clips

and screws provided.

1. Secure the spring clips (A) (fig. 1) with the screws

provided (B) (fig. 1) as shown, paying attention to the

specified distances.

2. Fit the hob into the worktop.

• If the worktop is made of marble, plastic, ceramic,

stone, etc., the hob must be secured with special

brackets (C) (fig. 2).

1. Fit the hob into the worktop (fig. 1).

2. Place the 4 brackets (C) in position in accordance with the

thickness of the worktop as shown in fig. 2.

3. Fasten the 4 screws (D) in the positions (E) (fig. 2).

Electrical connection

• Regulations require that the appliance be earthed.

• Connection to the mains must be carried out by a

qualified technician in accordance with the

manufacturer’s instructions and in compliance with local

regulations.

• The installer is responsible for connecting appliances

correctly to the mains and for observing the safety

regulations.

• The oven power cable must be long enough to connect

the built-in appliance to the mains.

• Observance of safety directives requires that a multi-

pole switch with a minimum contact gap of 3 mm be

used for the installation.

• Do not use multiple plug adapters or extension leads.

• After the oven has been installed, the electrical

components must be inaccessible.

Connecting the oven to the power supply

Note: the yellow/green earth wire must be connected to the

screw with the symbol .

• Strip approx. 70 mm of the cable sheath from the

power supply cable (G).

• Strip approx. 10 mm of sheath from the conductors.

Insert the cable (G) through the opening in the lid (F).

• Insert the cable into the cable clamp and connect the

conductors to the terminal block as indicated in the

diagram printed on the lid.

• Secure the power cable (G) by means of the cable

clamp.

• Refit the protection lid (F).

• After the electrical connection, fit the hob from the top

and hook it to the fixing springs, according to the

illustration.

Declaration of conformity

• This cooktop is suitable for contact with foodstuffs and

complies with EEC (CE) Regulation n. 1935/2004.

• This hob (Class Y) has been designed to be used only

for cooking. Any other use (such as heating a room) is

improper and dangerous.

• This hob has been designed, constructed and marketed

in compliance with:

- safety objectives of the “Low Voltage” Directive

2006/95/EC (which replaces 73/23/EEC and

subsequent amendments);

- the protection requirements of Directive

“EMC” 2004/108/EC;

- requirements of EEC Directive 93/68.

The Manufacturer reserves the right to change product

specifications without prior notice.

Fig. 1

Fig. 2

Fig. 3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool akm 702 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool akm 702

Whirlpool akm 702 User Manual - German - 2 pages

Whirlpool akm 702 User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Whirlpool akm 702 Manual

Product: