504048
2
Zoom out
Zoom in
Previous page
1/8
Next page
GB -2-
First time use
1
4
10
9
23
5
7
86
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set only
before the first wash or if water
hardness has been changed
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next
press of the start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
1. Ask your water supply company what the water hardness is... 2. ...enter this value on
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
Insert value is shown
in the display
Gel or Powder
(rinse aid and salt)
Tablet s
0 - 5 0 - 9 0 - 6.3 Soft 1
go to step 1
(see “Daily
check”)
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
if water is
HARD extra salt
needs to be added
(go to step 1,
“Daily check”)
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
At first time use, the salt
reservoir has to be filled
independently from water
hardness level (see description
below in step 1 “Daily check”).
1
Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
How to set water hardness in order to always assure the best cleaning results
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool ADPU 7452 6S IX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool ADPU 7452 6S IX in the language / languages: English as an attachment in your email.

The manual is 3,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool ADPU 7452 6S IX

Whirlpool ADPU 7452 6S IX Quick start guide - German - 8 pages

Whirlpool ADPU 7452 6S IX Quick start guide - Dutch - 12 pages

Whirlpool ADPU 7452 6S IX Quick start guide - French - 12 pages

Whirlpool ADPU 7452 6S IX User Manual - Norwegian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info