450668
5
Zoom out
Zoom in
Previous page
1/8
Next page
14
To ensure the dishwasher works at its best, soft
water, i.e. water that is lime-free, is required. The
presence of lime in tap water causes water stains
due to calcium deposits on crockery and glasses.
A water softening system has been built in the
dishwasher to ensure a steady supply of soft
water. This is basically a decalcifying system,
which needs to be regenerated regularly using
special dishwasher salt.
Setting the correct water hardness level:
Set the water hardness level by turning the
selector fitted on the left-hand side of the inner
appliance wall by using a coin. Use the table
below to set the dial to the correct setting:
If the water hardness level falls within category 1
(soft), no salt is required.
To find out the waterhardness level of water in
your area contact your local Water Board or
check the last bill you received.
If provided, a simple test can be employed to set
the hardness level using the hardness test strip.
Dip the test strip into a glass of water from the
tap.
Wait for 3 seconds, withdraw the strip from
the water.
Wait for 1 minute.
If all the three test squares are still green, set
the hardness selector to 0, and disregard all
instructions about salt usage.
If one of the test squares becomes red, set
the selector to 1.
If two of the test squares become red, set the
selector to 2.
If all of the test squares become red, set the
hardness selector to 3.
How to fill the salt container:
Warning: only use dishwasher salt!
Do not fill the salt container with
unsuitable substances, such as
detergent, as this will cause irreparable
damage to the water softener system.
1. Remove the lower rack.
2. Unscrew the cap by turning it counter-clockwise.
3. When first using the dishwasher: fill the salt
container with approximately 1 litre of water.
4. Fill the salt container to the rim with salt
(using the funnel provided) (when filling for
the first time use min. 1.5 kg and max. 2 kg)
and stir with a spoon handle.
5. Screw the cap back on by turning it
clockwise.
6. Fit the lower rack.
7. After filling the regeneration salt container,
immediately
start a wash programme (the
Prewash programme alone is not sufficient),
so as to eliminate any residual saline solution
straight away and avoid corrosion.
Check the salt level regularly.
Salt level indicator:
The dishwasher is equipped with an electric or
visual salt level indicator (depending on the
model installed).
Electric indicator:
The salt level indicator lamp on the control panel
lights up when the salt container is empty.
Visual indicator:
The green float is clearly visible in the cap
window when the salt container is sufficiently full.
The green float drops and is no longer visible
when the salt container needs to be refilled.
HOW TO FILL THE SALT CONTAINER
Water
hardness
category
German
degrees
°dH
French
degrees
°fH
Position
of the
selector
1 0 - 6 0 - 11 0
2 7 - 13 12 - 23 1
3 14 - 20 24 - 36 2
4 21 - 35 37 - 63 3
9LVXDOLQGLFDWRU
)XOO
(PSW\
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool ADP 253 WH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool ADP 253 WH in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool ADP 253 WH

Whirlpool ADP 253 WH Quick start guide - English - 4 pages

Whirlpool ADP 253 WH User Manual - German - 7 pages

Whirlpool ADP 253 WH User Manual - German - 8 pages

Whirlpool ADP 253 WH Quick start guide - Dutch - 4 pages

Whirlpool ADP 253 WH User Manual - Dutch - 8 pages

Whirlpool ADP 253 WH Quick start guide - French - 4 pages

Whirlpool ADP 253 WH User Manual - French - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info