120859

Wave Ceptor 2554 Manual

1
Zoom out
Zoom in
Previous page
1/4
Next page
USER’S GUIDE 2554
1
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
General Guide
• Press C to change from mode to mode.
• In any mode, press B to illuminate the display.
Date Alert Mode
Stopwatch Mode
Timekeeping Mode
Alarm Mode
▲
▲
▲
▲
Press C.
▲
World Time Mode
Time Recorder Mode
▲
Current Time Setting
This watch automatically adjusts its time setting in accordance with a time calibration
signal. You can also perform a manual procedure to set the time and date, when
necessary.
• Before using the watch in Western Europe, first use the procedure under “Setting Up
the Watch for Use in Western Europe” to set the time in accordance with a time
calibration signal.
• Note that after you set your Home City (the city where you normally use the watch)
code, you must also turn on the watch’s time calibration signal receiver if you want to
enable auto time calibration. See “About Auto Receive” for more information.
• See “Setting the Time and Date Manually” for information about manual settings.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• Pressing D displays the Last Signal screen (date and time the time calibration
signal was last received) in the Timekeeping Mode.
Last Signal Screen
▲
Press D.
Day of week
Receive date
Receive time
Month – Day Hour : Minutes Seconds
PM
indicator
▲
▲
▲
Alternate at the
1 second interval
Setting Up the Watch for Use in Western Europe
You need to make the following three settings before using this watch in Western
Europe. The following provides a general overview of the setting procedure. For full
details, see “Setting the Time and Date Manually” and “Time Calibration Signal
Reception”.
• Specify the city code for your Home City (the city where you will normally use the
watch).
• Select the auto summer time (DST) setting.
• Perform the manual time calibration signal receive operation to set the current time.
To set up the watch for use in Western Europe
1. In the Timekeeping Mode, hold down A until the
current auto receive on/off setting to flash, which
indicates the setting screen.
2. Press C to move the flashing to the city code setting.
3. Use D(+) and B(–) to select the city code you want to
use as your Home City.
City code
• The following are the city codes for major cities in the
Western Europe time zones.
BER and PAR: Berlin, Paris, Milan, Rome,
Amsterdam, Hamburg,
Frankfurt, Vienna
LON: London
4. Press C to display the summer time (DST) setting
screen.
5. Use D to select A (auto DST).
• Auto DST specifies auto switching between Daylight
Saving Time and Standard Time.
6. Press A to exit the setting screen.
7. Hold down D for about two seconds until the watch
beeps.
• Release D and the message RC! appears to indicate
that signal reception has started.
• Time calibration signal reception takes from two to six
minutes. Take care that you do not move the watch
during this time.
Receive indicator
• If the watch is indoors, we recommend that you place the watch near a window to
allow better signal reception.
• After signal reception is complete, the display of the watch changes to the Last
Signal screen.
Time Calibration Signal Reception
This watch is designed to pick up a time calibration signal and update its time setting
in accordance with the signal. There are two different methods you can use to receive
the signal: Auto Receive and Manual Receive. With Auto Receive, the watch
automatically receives the calibration signal three times each day and makes
appropriate adjustments. With Manual Receive, you perform a specific button
operation to receive the calibration signal.
Before performing a signal receive operation, remove the watch from your wrist and
position it as shown in the illustrations below.
• If your watch has a resin band, pass the end of the band through the band loop and
place the watch on a stable surface.
Resin band Metal band
Pass through band loop.
Note
• If you are using the time calibration signal to set the time for this watch, be sure to
correctly set your Home City. Otherwise, there is the chance that the watch will not
set the correct time. See “Setting the Time and Date Manually” for details.
• Note that signal reception is possible only when the watch is within range of a time
calibration signal transmitter, and BER, PAR, LON, or ATH is selected as the Home
City code.
• See “City Code Table” for a complete list of available city codes.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
• Auto receive is turned on when the watch is shipped from the factory.
• See the information under “Time Calibration Signal Reception” if you experience
problems with time calibration signal reception.
To perform manual time calibration signal reception
1. Place the watch on a stable surface so its top (12 o'clock side) is facing in the
general direction of the signal transmitter.
• Note that signal reception is poor if the watch is on its back or side.
2. In the Timekeeping Mode, hold down D for about two
seconds until the watch beeps.
• Release D and the message RC! appears to indicate
that signal reception has started.
• Time calibration signal reception takes from two to six
minutes. Take care that you do not move the watch
during this time.
• After signal reception is complete, the display of the
watch changes to the Last Signal screen.
• The receive indicator indicates that the time calibration
reception attempt was successful.
Receive indicator
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press D.
• If the receive operation is unsuccessful, the message ERR appears on the display
for about one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the Last Signal or ERR screen to the normal timekeeping
screen by pressing D.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wave Ceptor 2554 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wave Ceptor 2554 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info