805503
7
Zoom out
Zoom in
Previous page
1/8
Next page
7
HU DE
Környezeti feltételek
(hőmérsékletek)
Üzemi/Szállítási és tárolási
0°C - +40°C
-10°C – tól +50°C –ig
Tápellátás 230V ac 50Hz
Védelmi osztály Class II - IP33
Csatlakozás típusa
Maximum kapacitás
2 eres (szabad kontakt), csatlakozó kábelek <1.5mm2.
8A –ig 250Vac 50Hz
Rádiófrekvencia tartomány 868 MHz, <10mW
Normák és konformitás:
Az Ön termosztátját a következő
normák, direktívák és előírások
alapján gyártottuk:
EN 60730-1:2017 / EN 60730-2-9:2021 / EN IEC 61000-3-2:2019 + AMD1:2021
EN IEC 61000-3-3:2013 + AMD1:2017 + AMD2:2021 / EN 55014-1:2017
EN 55014-2:2015 / EN 55024:2010 + A1:2015 / ETSI EN 301 489-3 V2.1.1
ETSI EN 301 489-1 V2.2.3 / ETSI EN 300 220-1 V3.1.1 / ETSI EN 300 220-2 V3.2.1
EN IEC 63000:2018 / Regulation (EU) 2015/1188 / Regulation (EU) 2013/813
Műszaki adatok
Rádiófrekvenciás konguráció
1. Helyezze üzembe a jelfogót a következő utasításoknak megfelelően: A beüzemelés előtt tartson szem előtt néhány
rutinszablyályt, melyek az optimális működést biztosítják.
- A jelfogót legalább 50 cm távolságra kell minden elektromos vagy vezeték nélküli készüléktől (GSM, Wi-Fi router)
elhekyezni
- Mielőtt a vezetékes munkát elvégezné, a jelfogót áramtalanítani kell!
- Csatlakoztassa a jelfogót a hálozatba!
2. Majd 5 másodperc hosszan nyomja meg a jelfogó gombját, a zöld RF LED lámpának kell tartósan felgyulladnia,
jelezvén, hogy a jelfogó most rádófrekvenciás kongurációs módban van és várakozik a termosztát kongurációs jelére.
3. A termosztát használati utasításában megtalálja az “RF Init” módot, a kongurálás elvégzéséhez!
4. Ellenőrizze, hogy a jeleket a jelfogó hibamentesen fogadja! A jelfogón , a zöld LED-nek kell villognia, ahogy a
termosztát rádiófrekvenciás jeleit fogadja.
5. Lépjen ki a termosztát kongurációs üzemmódjából (Nézzen utána a termosztát használati utasításában)!
6. Az installációja most üzemkész.
Umgebungstemperturen
Umgebungstemperatur
Transport- / Lagertemperatur
0°C - +40°C
-10°C bis +50°C
Speisespannung 230V ac 50Hz
Schutzklasse / Schutzart Klasse II - IP33
Schaltkontakt
Schaltleistung
2 Drähte (freier Kontakt) - Schraubklemmen <1,5 mm2
Bis zu 8A - 250VAC, 50Hz
Funkfrequenz 868 MHz, <10mW
Normen und Konformität:
Der Einzelempfänger wurde in
Übereinstimmung mit den folgenden
Normen und Normdokumenten
konstruiert
EN 60730-1:2017 / EN 60730-2-9:2021 / EN IEC 61000-3-2:2019 + AMD1:2021
EN IEC 61000-3-3:2013 + AMD1:2017 + AMD2:2021 / EN 55014-1:2017
EN 55014-2:2015 / EN 55024:2010 + A1:2015 / ETSI EN 301 489-3 V2.1.1
ETSI EN 301 489-1 V2.2.3 / ETSI EN 300 220-1 V3.1.1 / ETSI EN 300 220-2 V3.2.1
EN IEC 63000:2018 / Regulation (EU) 2015/1188 / Regulation (EU) 2013/813
Technische Daten
Funk-Initialisierung
1. Installieren und verbinden Sie den Empfänger gemäß den folgenden Richtlinien: Achten Sie besonders auf die Standortwahl
Ihres Receivers, denn für einen optimalen Betrieb Ihrer Anlage müssen einige Vorkehrungen getroffen werden:
- Der Funkempfänger sollte nicht zu nahe an elektrischen oder hydraulischen Rohren oder irgendeiner Art von drahtlosem
Kommunikationsgerät (GSM, Wi-Fi usw.) platziert werden. Ein Abstand von ca. 50 cm garantiert einen optimalen Betrieb.
- Unterbrechen Sie unbedingt die Stromversorgung, bevor Sie an den Anschlussklemmen eingreifen.
- Schließen Sie Ihren Receiver an das Stromnetz an.
2. Drücken sie die Taste Funk-Initialisierung für ca. 5 sec. , die grüne Funk LED sollte aufleuchten. Der Einzelempfänger befin-
det sich nun im Funk-Initialisierungsmodus und ist für die Zuordnung eines Thermostaten bereit.
3. Bitte beachten Sie die Bedienungsanleitung des Funk-Thermostaten und bringen Sie diesen in den Modus Funk-Konfigurati-
on “RF Init”.
4. Stellen Sie sicher, dass der Funk-Empfänger das Funk-Signal erhalten hat. Am Empfänger sollte die grüne LED beim Emp-
fang eines Funk-Signals blinken.
5. Verlassen Sie die Funk-Konfiguration am Thermostaten. (Bitte die entsprechende Bedienungsanleitung beachten)
6. Der Einzelempfänger ist nun betriebsbereit.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Watts WAT BT-RRF FREE CONTACT - Wireless Wall receiver at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Watts WAT BT-RRF FREE CONTACT - Wireless Wall receiver in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info