805573

Watts BT-OS02 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
PPLIMW15086Ae
52mm
80mm
“ RF init ”
Wireless outside temperature probe
1. INSTRUCTION
- The probe must be placed on the wall with the enclosed screws, or otherwise if the support is not
appropriated.
Once fixed on the wall, don’t forget to put the rubber caps provided to ensure the tightness of the box
against dripping water.
- the probe must be preferably placed on a north or north/west wall sheltered for weather and away from
parasites of heat sources such suction, exhaust air of the building, …
2. INITIALISATION RF
- Switch on the RF outdoor probe
- In the central unit, go in the installer menu / Radio pairing and select “External Probe” device. Press on
Radio Pairing icon.
The bicolor LED blinks and informs you about the status of the transmission between the probe and the
central unit:
- Red : communication problem, the synchronization is not successful, you must restart the
initialization process by moving the probe (see note 1)
- Green : success, the synchronization is successful, you can now fix permanently the probe.
After flashing red or green LED turns off, the synchronization is complete.
Note 1 : Avoid metal surfaces between the probe and the Central that can disturb radio communications. It
is then recommended to move the probe away from the obstacle.
3. TECHNICAL CARACTERISTICS
Operating temperature
- 50°C to 65°C
Power supply
Operating life
1 Lithium AA battery (LR06) 2600mAh
10 years
Radio Frequency
868.00 MHz <10mW.
Range of approximately 180m in open space.
Range of approximately 30m in residential environment
Homologations
EN 300220-1, -2 / EN 301489-1, -3
R&TTE
Protection Marking
IP 65
Status LED
Blinking green (flash 10sec)
Blinking reg (2 flash / ~ 10min)
RF initialization
Low batteries
4. BATTERY REPLACEMENT
- If the status led of your RF probe blinks red during a transmission (every 10 minutes approximatively), it
will be necessary to replace the battery.
- Switch off your RF probe
- Take off the used battery (Do not throw your battery in the trash, recycle as it should be)
- Put the new battery
- Switch ON your probe (pointing up), the led status blinks green.
- Wait 10 seconds to see if the communication is correct: the green LED blinks
- Close the box
52mm
80mm
80mm
Note :
Before permanently attaching the probe,
redo the initialization step with the Central to
valid the choice of location.
Push button
Status LED
Battery
“ RF init ”
Sonde de température extérieure sans fil
1. CONSEILS D’INSTALLATION
- La sonde doit être fixée au mur avec l’ensemble vis & chevilles fournies, ou autre si le support ne
convient pas.
Une fois fixée contre le mur n’oubliez pas de mettre en place les capuchons en caoutchouc fournis afin de
garantir l’étanchéité du boîtier contre les ruissèlements d’eau.
- La sonde doit être placée de préférence sur une paroi nord ou nord/ouest à l’abri des intempéries et
éloignée de source de chaleurs parasites type ventouse, extraction d’air du bâtiment, etc…
2. INITIALISATION RF
- Retirez le film protecteur de la batterie sur la sonde extérieure RF
- Allumer la sonde extérieure RF
- Dans l'unité centrale, allez dans le menu installateur / Appairage radio et sélectionnez l'appareil «Sonde
externe». Appuyez sur l'icône de couplage radio.
Le voyant LED bicolore clignote et vous renseigne sur l’état de la transmission entre la sonde et le
récepteur :
- Rouge : problème de communication, la synchronisation n’est pas réussie, vous devez
recommencer la procédure d’initialisation en déplaçant la sonde (cf note 1)
- Vert : succès, la synchronisation est réussie, vous pouvez maintenant fixer définitivement la
sonde.
Après avoir clignoté en rouge ou vert, le voyant s’éteint, la synchronisation est terminée.
Note 1 : Evitez les surfaces métalliques situées entre la sonde et la centrale qui peuvent perturber la
communication radio. Il est alors préconisé de déplacer la sonde pour s’éloigner de l’obstacle.
3. CARACTERISTIQUES
Température de fonctionnement
-50°C à 65°C
Tension d’alimentation
Autonomie
1 piles Lithium type AA (LR06) 2600mAh
10 ans
Radio Fréquence
868.00 MHz <10mW.
Distance de fonctionnement en champ libre 180 mètres
Distance de fonctionnement en milieu résidentiel 30
mètres
Homologations radiofréquences
EN 300220-1, -2 / EN 301489-1, -3
Conforme aux exigences R&TTE
Indice de Protection
IP 65
Voyant d’état
Clignotement vert (flash 10sec)
Clignotement rouge (2 flash / ~ 10min)
Initialisation RF
Piles faibles
4. REMPLACEMENT DE LA PILE
- Si le voyant de votre sonde clignote rouge pendant une transmission (toutes les 10min environ), il sera
nécessaire de changer la pile.
- Retirez la pile usagée (Ne jetez pas votre pile à la poubelle, recyclez-la comme il se doit)
- Mettre la pile neuve en place
- Attendez 10 secondes pour voir que la communication est bonne : le voyant clignote en vert
- Refermez la boîte.
80mm
Remarque :
Avant de fixer définitivement la sonde, faire
l’étape d’initialisation avec la centrale pour
valider le choix de l’emplacement.
Bouton poussoir
Voyant de
signalisation
Pile
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Watts BT-OS02 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Watts BT-OS02 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info