Manual VTech RM7766HD (page 1 of 2) (English)

809795

Zoom out

Zoom in

1/2

Frequency Baby unit: 2412 - 2472 MHz

Channels 13

LCD 7’’ Colour LCD

(IPS 1280x800 pixels)

Nominal effective range Actual operating range may vary according to environmental conditions

at the time of use.

Power requirement Baby unit power adaptor: Output: 5V DC, 1000mA.

Parent unit power adaptor: Output: 5V DC, 2A.

Parent unit battery: 3.7V 5000mAh, 18.5Wh Lithium-ion battery

Specifications are subject to change without notice.

Technical specications

RM7766HD

7” Smart Wi-Fi 1080p

Pan & Tilt Monitor

Quick start guide

Status icons

Direct mode

The parent unit and baby unit

connect to each other directly.

Red bars indicate no connection.

Router mode

The parent unit and baby unit

connect via the Wi-Fi network.

The red icon on the baby unit or

parent unit, indicates no connection

between the respective unit(s) and

the router.

Black and white night vision is

activated.

Motion detection alert is turned on.

Sound detection alert is turned on.

Melodies or soothing sounds are

playing.

Night light is on.

Auto night light brightness is

activated.

Parent unit speaker is muted.

Temperature alert is turned on.

21 Temperature (Blue: lower than 20°C;

White: between 20-24°C;

Orange: higher than 24°C)

Battery level indicator

Low battery indicator.

The applied nameplate is located at the bottom of the baby

unit’s base.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of ﬁre, electric shock

and injury, including the following:

1. Follow all warnings and instructions marked on the

product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above

2 metres.

4. This product is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be

used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water, for example, near to a

bath, sink, swimming pool or shower.

7. CAUTION:

Use only the battery provided. There may be a

risk of explosion if a wrong type of battery is used for the

parent unit. The battery cannot be subjected to high or low

extreme temperature and low air pressure at high altitude

during use, storage or transportation. Disposal of battery

in ﬁre or a hot oven, mechanically crushing or cutting the

battery can result in an explosion. Leaving the battery in an

extremely high temperature surrounding environment can

result in an explosion or the leakage of ﬂammable liquid of

gas. Battery subjected to extremely low air pressure may

result in an explosion or the leakage of ﬂammable liquid or

gas. Dispose of used batteries according to the instructions

8. Use only the power adaptors included with this product.

Incorrect power adaptor polarity or voltage can seriously

damage the product.

Power adaptor information:

Parent unit output: 5V DC 2A

VTech Telecommunications Ltd.

Model: VT07EUK05200 (UK)

Baby unit output: 5V DC 1A

VTech Telecommunications Ltd.

Model: VT05EUK05100 (UK)

Rechargeable battery information:

3.7V 5000mAh, 18.5Wh Lithium-ion battery

Zhuhai Great Power Energy Co., Ltd.

Model: GSP806090-5Ah-3.7V-1S1P

9. The power adaptors are intended to be correctly oriented

in a vertical or ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet should

be installed near the equipment and should be easily

accessible.

11. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

12. Do not modify the power adaptors or replace with other

adaptors, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not

install this product where the cords may be walked on or

crimped.

14. This product should be operated only from the type of

power source indicated on the marking label. If you are

not sure of the type of power supply in your home, consult

your dealer or electricity supply provider.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand

or other unstable surfaces.

17. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back

or bottom of this product are provided for ventilation. To

protect them from overheating, these openings must not be

blocked by placing the product on a soft surface such as a

bed, sofa or rug. This product should never be placed near

or over a radiator or heat source.

18. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

19. To reduce the risk of electric shock, do not isassemble

this product, but take it to an authorised service

acility. Disassembling or removing parts of the

product other than via the battery door may expose

you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the

product is subsequently used.

20. You should test the sound reception every time you turn

on the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset

the baby monitor periodically by powering off and then

powering on the units, and power off the baby monitor if

you are not intending to use it for some time.

23. The small parts of this monitor can be swallowed by

babies or small children. Keep these parts out of reach of

children

24. Children should be supervised to ensure that they do not

play with the product.

25. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 0oC

and 40oC.

2. Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as

bright sunshine or ﬁre.

4. Mishandling batteries can cause burn, ﬁre or explosion

hazards.

5. Warning—Strangulation Hazard—Children

have STRANGLED in cords. Keep this cord out

of the reach of children (more than 0.9m away.

Do not

remove warning label on the adaptor

cord

6. Never place the baby unit(s) inside the baby’s crib or

playpen. Never cover the baby unit(s) or parent unit with

anything such as a towel or a blanket.

7. Other electronic products may cause interference with

your baby monitor. Try installing your baby monitor

as far away from these electronic devices as possible:

wireless routers, radios, cellular telephones, intercoms,

room monitors, televisions, personal computers, kitchen

appliances and cordless telephones.

For better security and more stable connectivity, this baby monitor requires

connecting to a Wi-Fi network and operating in Router mode connection.

Direct mode

Your baby monitor parent unit and baby unit connect to each other in Direct mode by default,

which allows you to immediately stream video out of the box.

It is NOT recommended to continue using Direct Mode connection after initial installation.

You may experience reduced signal strength

if your parent unit and baby unit are far apart,

or there are obstructing factors, such as

internal walls, between them. You have to set

up Router mode to connect the units via your

home Wi-Fi network to improve the

connection between your parent unit and

baby unit.

Router mode

You are required to set up your monitor

in Router mode to enjoy live video

streaming via your parent unit with an

enhanced connection. Router mode

is the recommended mode for stable

connectivity.

Router mode uses your home Wi-Fi

network to connect your video monitor. It

supports live video streaming through the

parent unit and smartphone app.

If you want to stream live video remotely

with your mobile device, download and

install the MyVTech Baby Pro mobile app.

With the mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD

video monitor system. It serves as a communicating channel between your baby unit and mobile

device, allowing you to monitor and/or control your baby unit wherever you are. For more

details, see Download app for mobile access section in this quick start guide.

Note

• When both parent unit and app are viewing the camera simultaneously,

the video quality will be optimised to deliver the best possible viewing result.

Overview

What’s in the box

Connect, charge and power on the baby monitor

x 2 x 2

Quick start guide

Your baby monitor package contains the following items. Save your sales receipt and original

packaging in the event warranty service is necessary.

How the system works Parent unit icons

For mobile access:

MyVTech Baby Pro mobile app

Network Wi-Fi

Wi-Fi router 2.4GHz 802.11 b/g/n

Internet connection 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload

bandwidth per baby unit

Requirements

Main

Menu Options

Night light

• Turn on or turn off night light.

• Select a night light colour.

• Adjust night light brightness.

• Set a night light timer.

Melodies and soothing sounds

• Select play all melodies, or play

one of the ﬁve melodies and ﬁve

soothing sounds.

• You can also set the timer to stop

playing after 15, 30 or 60 minutes,

or playing non-stop.

Alerts - Sound, motion and temperature

• Turn on/off sound detection,

motion detection, and

temperature alerts.

• Select the sound and motion

sensitivity level.

• Turn on/off Auto Wake-up .

• Select maximum and minimum

temperature for alert range.

• Set the temperature format to

Fahrenheit (oF) or Celsius (oC).

Parent unit settings

• Adjust parent unit screen brightness.

• Adjust Low Battery Alert Tone

volume.

• Adjust No Link Alert Tone volume .

Baby unit settings

• Turn on/off Night Vision.

• Turn on/off baby unit Status LED.

• Adjust baby unit speaker volume.

General settings

• Connect to home Wi-Fi network.

• Connect mobile phone.

• Reset Settings to factory default.

• Software Update.

Connect the baby monitor

• The rechargeable battery in the parent unit is built-in.

• Use only the power adaptors supplied with this product.

• Make sure the parent unit and the baby unit are not connected to an electronically controlled electric outlet.

• Connect the power adaptors in a vertical or ﬂoor mount position only. The adaptor prongs are not

designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling,

under-the-table, or cabinet outlets. Otherwise, the adaptors may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adaptor cords are out of reach of children.

Charge the parent unit battery before use

The parent unit operates on an internal rechargeable battery or AC power. To continuously

monitor your baby, keep the parent unit connected to AC power.

• Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours. When

the parent unit battery is fully charged, the battery icon becomes solid .

• The standby time varies depending on your actual use.

The parent unit turns on automatically after connecting to the power socket, and the

welcome screen appears. You can press Power o turn the parent unit on or press and

hold to turn it off.

The battery icon indicates the battery status (see the following table).

Battery indicators Battery status Action

alert displays on the parent unit

screen, and the battery icon shows

empty , with the LED light

ﬂashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without

interruption

(about 30

minutes).

The battery icon becomes solid . The battery is fully

charged.

To keep the battery

charged, connect it to AC

power when in use.

Slide the switch to ON to power on your baby unit.

• When powering up, the baby unit’s status LED turns on.

It will turn off after a while and remains off.

• The status LED is set to off by default. If you want to

keep the LED on, press MENU, then go to

> Status LED and turn it on.

NOTE:

Camera lens and surface may get

warm during normal operation.

WARM

Parent unit overview

1LINK LED light

• On when the parent unit is linked to the

baby unit.

• Flashes when the link to the baby unit

is lost.

2 LED light

• On when the parent unit is connected to

AC power, and the battery is charging.

• Flashes when the parent unit battery is

low and needs to be charged.

33- level sound indicator light

• Green: low sound level is detected by

the baby unit.

• Green and amber: moderate sound

level is detected by the baby unit.

• Green, amber and red: high sound level

is detected by the baby unit.

4TALK /

• Press and hold to talk to the baby unit.

• While in a sub-menu, press to exit.

5MENU | SELECT

• Press to enter the main menu.

• While in a menu, press to choose an

item, or save a setting.

6 | | | Arrow keys

• Press to navigate leftward, upward,

rightward or downward, within the

main menu and sub-menus.

• Press to move the baby unit camera

leftward, rightward , upward or

downward.

7 |

• Increase or decrease parent unit

volume.

8 Zoom

• Press to zoom in/out.

• While in a sub-menu, press to view the

help menu.

9 Power | LCD ON/OFF

10 Microphone

11 Antenna

12 Speaker

13 Power jack

14 RESET

• Force reboot the parent unit.

15 Stand

Mobile access

Connecting Wi-Fi to

enhance local access

Important safety instructions

Raise the parent unit

antenna for better

reception

Press the Power key

1Light sensor

2Camera lens

3Infrared LEDs

• Allow you to see clearly in a dark environment.

4Microphone

5Night Light

6 Night Light Control Key

• Go to Night Light section to learn more.

7LED indicator

• Steadily on, then off, when the baby unit is

connected to the parent unit.

• Flashes when the baby unit is connecting with

the parent unit, or the link to the parent unit

has lost.

8ON/OFF switch

• Power it on or off.

9Speaker

10 Temperature sensor

11 Power jack

12 Wall mount slots

13 PAIR

• The parent unit and baby unit provided are

already paired.

• Reset the baby unit to factory default.

1. Press and hold PAIR key until you hear a

beep sound.

2. Release the PAIR key, and then press the

PAIR key again ﬁve times until you hear

another beep sound.

3. The baby unit will sound another beep

when the reset completes. Then, the

baby unit will reboot.

Baby unit overview

Basic operation

Talk to your baby via the baby unit

1. Press and hold the TALK key.

2. When the icon displays on

screen, speak to your parent unit.

Your voice is transmitted to the

baby unit.

3. When ﬁnished talking, release

the TALK key to hear your baby

again.

Turn on/off baby unit's status LED

Turn on or turn off the baby unit status LED

indicator. Go to:

> Status LED.

Zoom

Press to zoom in or out in a ﬁxed

zoom sequence. indicates that the

image is magniﬁed 3 times.

Adjust speaker volume

Press | to adjust the parent unit

speaker volume level received from the

baby unit.

After powering up your video monitor, the parent unit streams live video in direct mode.

We recommend you follow the instructions on screen to set up home Wi-Fi network

with your monitor for functionality enhancements and mobile access. See Auto software

and rmware update and Download app for mobile access in this quick start guide.

Use the menu

Press MENU on the parent unit to enter the

main menu, choose a menu item, or save a

setting. You can use the parent unit menu

for advanced settings or operations, such

as to play or stop the baby unit lullaby, or

adjust the baby unit sound sensitivity.

While in the menu:

• Press | | | to scroll among the

menu options.

• Press SELECT to select an item.

• Press TALK to return to the live video.

• Press to go to the Help & info page.

To restore to the default settings or reset the Wi-

Fi connection, you can reset the parent unit by

pressing the RESET key at the back of the unit.

Insert a pin into the RESET hole on the back of

the parent unit, and then gently press the key

inside.

Turn on/off the parent unit screen

You can turn on or turn off the parent unit

screen without powering off the unit. You

will still hear sounds from the baby unit.

• Press | LCD ON/OFF on the parent unit

to turn off the screen.

• Press any key on the parent unit to turn

the screen on again.

Muted

Press and hold

Press the Power key

b) From app store

1. Browse the App Store or the Google Play store .

2. Search for the mobile app with the keyword “myvtech baby pro“.

3. Download and install the MyVTech Baby Pro mobile app to your mobile device.

Scan the QR code on the right to get the app.

• Make sure your mobile device meets the minimum

requirement for the mobile app.

Minimum requirement

The mobile app is compatible with:

• AndroidTM 6.0 or later; and

• iOS 12 or later.

a) From parent unit

• Before installing the app, please connect your baby monitor to your Wi-Fi network.

Press MENU on the parent unit, go to , and select “Congure Wi-Fi”to set up the

Wi-Fi connection.

1. Press MENU.

2. Go to > Connect Mobile Phone.

3. Scan the QR code in the parent unit to download the app into your mobile

device.

Download app for mobile access

App installation

In your mobile device:

1. Tap to run the mobile app, and then create a user account.

2. We recommend that you use common webmail services, such as Google

Gmail for registration of your user account. Check your email (and Spam

folder), and activate your new camera account via the email link, then sign in to

your account.

2Set up user account

Add camera

Follow the instructions in the mobile app to pair the camera. Tap , then Add Camera

in the mobile app to get started.

Local access

Local access, for

start up quick view

and setup stage.

Scan to learn more

on improving

connectivity.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of VTech RM7766HD in the language / languages: English as an attachment in your email.

The manual is 6.56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

VTech RM7766HD Manual

Product: