809830

VTech BM3300 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has all the feature operations
and troubleshooting necessary to install and
operate your new VTech product. Please
review this manual thoroughly to ensure
proper installation and operation of this
innovative and feature rich VTech product.
What’s in the box
Install the battery
The parent unit runs on a rechargeable battery
or AC power. To continuously monitor your
baby, make sure you use both battery and
AC power at the same time. With the battery
alone, the parent unit can cordlessly run for a
short time only.
NOTES
Use only the battery supplied with this product.
The operating time for using the rechargeable
battery is short. If you want to monitor your baby
for a long time, we recommend you connect the
parent unit to AC power.
If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
Install the battery as shown below.
NOTES
Make sure the label THIS SIDE UP is facing up
while inserting the battery.
Replace the battery
To replace the battery, pull out the battery
compartment cover, and then lift up the
battery. Follow the steps above to install the
new battery.
•
•
•
•
Connect and charge the
battery
NOTES
Use only the power adaptors supplied with this
product.
The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if they are plugged into a ceiling, under-the-table
or cabinet outlet.
Make sure the parent unit, the baby unit and
the power adaptor cords are out of the reach of
children.
Connect the baby monitor
•
•
•
Charge the parent unit battery
When you have connected the parent unit and
installed its battery for the first time or after
power outage, the parent unit will power on
automatically. The battery icon indicates the
battery status (see the following table).
NOTES
The parent unit battery is fully charged after
11 hours of continuous charging.
It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
The standby time varies depending on the
volume level you set, your actual use and the
age of the battery.
Battery
indicators
Battery
status
Action
The battery
icon is off
and
displays.
No battery
is installed
but operates
using AC
power, or the
battery has
been installed
incorrectly.
Install the
parent unit
battery.
Charge
without
interruption
(at least
30 minutes).
The screen
displays
Battery low
at Parent
Unit and .
The lightlight
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about
30 minutes).
The battery
icon
becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
•
•
•
Before use
NOTES
This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You should test the baby monitor before initial
use, and at regular times thereafter.
CAUTION
For hearing protection, make sure the
parent unit is more than 1 metre (3 feet)
away from the baby unit. If you hear any
high-pitched noise, move the parent unit
further away until the noise stops. You can
also press VOL- on the parent unit to lower
or mute the noise.
Make sure your baby unit and parent unit
are on.
The parent unit displays images from the
baby unit.
Speak towards the microphone of the
baby unit. You will hear the sound at the
parent unit.
NOTES
When the parent unit displays No link to
Camera, and the LINK LED light flash, move the
parent unit closer to the baby unit (observe the
minimum distance of 1 metre/ 3 feet). You can
also check if the baby monitor is connected to a
live power socket and switched on.
TIP
Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby unit.
•
•
1.
2.
•
•
•
Positioning the baby monitor
CAUTION
Keep the baby unit out of the reach of your baby.
Never place or mount the baby unit inside the
baby’s cot or playpen.
NOTE
To avoid interference from other electronic
devices, place your baby monitor far away from
devices such as wireless routers, microwaves,
mobile phones and computers.
Place the baby unit more than 1 metre
(3 feet) away from your baby.
Place the parent unit more than 1 metre
(3 feet) away from the baby unit.
3. Flip down the camera on the baby unit
to adjust the angle according to your
preference.
CAUTION
The default volume of your parent unit is level 4.
If you experience high-pitched screeching noise
from your baby monitor while positioning:
Make sure your baby unit and parent unit are
more than 1 metre (3 feet) apart, OR
Turn down the volume of your parent unit.
•
•
1.
2.
•
-
-
Operating range
The operating range of the baby monitor is
up to 300 metres (1,000 feet) outdoors or
50 metres (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions and other
interferences such as walls, doors and other
obstructions.
Overview
Baby unit overview
1Light sensor
2Camera
3Infrared LEDs
4-/VOLUME/+
Press to adjust the speaker volume.
It determines the talkback volume
transmitted from your parent unit.
•
5Microphone
6ON/OFF LED light
On when the baby unit is turned on
and is paired to the parent unit.
Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
•
•
7 ON/OFF switch
Slide to turn the baby unit on or off.•
8Temperature sensor
9Speaker
10 Threaded socket
For wall mount installation use.•
11 Power Jack
12 PAIR
Your baby unit and parent unit
provided are already paired.
•
Parent unit overview
1 LCD display
2 Zoom
Press to zoom in or out while
viewing images.
•
3
4
• Turn the volume up when the
speaker is on.
While in a menu, press to scroll up,
or to enter an item’s sub-menu.
While zooming, press and hold to
move the zoomed image up.
• Turn the volume down when the
speaker is on.
While in a menu, press to scroll
down.
While zooming, press and hold to
move the zoomed image down.
•
•
•
•
5MENU/SELECT
Press to enter/exit the menu.
While in a sub-menu, press to
choose an item, or save a setting.
•
•
6
While in a menu, press to choose
the next item on the left, or enter
into the submenu, if any.
While zooming, press and hold to
move the zoomed image to the left.
While in a menu, press to choose
the next item on the right, or return
to the main menu while in submenu.
While zooming, press and hold to
move the zoomed image to the
right.
•
•
•
•
7 On/off
Press and hold to power on.
Press and hold again to power off.
•
•
8TALK
Press and hold to talk to the baby
unit.
•
9PATROL
10 LCD ON/OFF
Press to turn the LCD screen on or
off.
•
11 Speaker
12 Power jack
13 Battery compartment cover
14 Stand
Parent unit lights
LINK On when the parent unit is linked to
the baby unit.
Flashes quickly when the link to the
baby unit is nearly lost.
On when the parent unit is
connected to AC power, or the
battery is charging.
Flashes when the parent unit
battery is low and needs charging.
Off when the parent unit is
disconnected from AC power.
TALK On when the parent unit is talking to
the baby unit.
On when the speaker volume of the
parent unit is turned off.
Parent unit status icons
Connection status
or displays when strong
signal strength is detected
between the baby unit and the
parent unit.
or displays when moderate
or low signal strength is detected
between the baby unit and the
parent unit.
displays when the link between
the baby unit and the parent unit
is lost.
•
•
•
Zoom
Displays when the camera at the
baby unit has zoomed in.
•
Night vision
Displays when the baby unit has
activated the night vision feature.
•
Lullaby
Displays when a lullaby is playing.•
Talkback
Displays when talking back to the
baby unit from the parent unit.
•
6-level sound indicator
Displays the sound level when there
is sound transmitted from the baby
unit.
(1 to 2 bars) indicates low sound
level detected by the baby unit.
(3 to 4 bars) indicates
moderate sound level detected by
the baby unit.
(5 to 6 bars) indicates high
sound level detected by the baby
unit (e.g. baby crying loudly).
•
•
•
Mute alert
Displays when the parent unit
speaker volume is set to off.
•
or
Real-time temperature
Displays the real-time temperature
detected by the baby unit in
Fahrenheit (oF) or Celsius (oC)
(e.g. 57
oF or 14
oC).
•
Battery status
animates
when the battery is charging.
displays solid when the
battery is fully charged.
displays when the battery is
low and needs charging.
•
•
•
AC power without battery
Displays when the parent unit is
connected to AC power without
the battery.
•
Speaker volume
Displays the parent unit speaker
volume level while adjusting.
•
Parent unit main menu icons
Brightness
You can change the brightness of
the parent unit screen.
Pairing baby unit
The baby unit and parent unit
provided are already paired.
Unpairing baby unit
You can remove the paired baby
unit.
LCD screen off timer
You can set a specific time for the
parent unit screen to switch off.
Temperature
You can turn on the Temperature
alert tone on so that the parent
unit beeps whenever the room
temperature detected by the
baby unit falls outside the desired
temperature range.
Lullaby
You can select, play, or stop a
lullaby.
Parent unit warning icons and
messages
/No link to
Camera
The baby unit is out of
range or is turned off.
/Battery low
at Parent Unit
The battery is empty and
needs to be recharged.
Pairing or unpairing is
complete.
Pairing or unpairing is in
progress.
Pairing or unpairing has
failed.
/Temperature
too high
or
/Temperature
too low
The temperature
detected by the baby unit
is higher/lower than the
desired temperature alert
range.
or or
or
or
The baby unit is unpairing
from the parent unit.
The parent unit is
searching for baby unit.
BC
User’s manual
BM3300
Safe & Sound®
2.8” Colour
Video Baby Monitor
For product support please call
01235 546810
> 1m (3ft)
DC 6V 500mA
MANUFACTURED IN CHINA
www.vtechphones.com
VTech Customer Service
1-800-595-9511
FCC ID: EW780-0617-00
IC: 1135B-80061700
4H20
I.T.E.
PAIR
e
d
a
b
c
h
i
f
g
j
k
l
＜1m (3ft)
＞1m (3ft)
THIS SIDE UP
THIS SIDE UP
> 1m (3ft)
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VTech BM3300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VTech BM3300 in the language / languages: English as an attachment in your email.

The manual is 4.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info