Manual Vivanco ur 850 lcd (page 1 of 8) (English, German, French, Italian)

122705

Zoom out

Zoom in

1/8

UR 850 LCD Universal Controller

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: hotline@vivanco.de 1

(GB) Operating Instructions

Vivanco UR 850 LCD remote control for

practically all TV, audio, video and other

infrared-controllable devices

Inserting the batteries

Open the battery compartment on the back of the

device, push the flap down lightly and insert 2 AA

alkaline batteries. Make sure that the polarity on the

batteries and in the battery compartment correspond

(thick spring = cell at bottom = -) and then close the

lid carefully. – Use undamaged batteries only.

Adapting to devices

In order to control your devices you must adapt or

set the remote control to them. There are two ways

of doing so: direct control code entry or code

search.

If the UR 850 LCD does not understand you it

displays ERROR and you can then repeat the entry.

Direct control code entry

Example: setting the remote control for a Philips TV

set:

1. Switch on your device, e.g. the TV, set to any

station.

2. To prepare code entry, briefly press the SET

button in the bottom right corner of the keypad, then

the required device button, e.g. TV. A brand and a

code number appear, see diagram.

– You cannot enter

a new code if you have activated the code entry lock.

3. Select the brand of your device, in this

example Philips, with  or . The first available

code in the device list is displayed.

4. Press a few buttons to determine whether you

have found a suitable code. When the code

corresponds to your device, press OK and the

setting for this device is completed.

5. If the code you have found does work at all or

not properly, try another code by selecting the next

code for the brand using the  or  button, then

test the code as described above under 4. and, if

successful, confirm with OK.

6. To set the remote control for other devices,

proceed in the same way. Instead of the TV device

button, press another button, e.g. VCR, CBL/SAT

(DVB-T, DECODER), DVD, TUNER, TAPE, CD,

AUX).

-Before setting a code and performing the subsequent test

for recording or playback devices, please insert a medium

(tape, CD, cassette, DVD, etc.).- You can interrupt code

entry at any time by pressing EXIT.

Code search

If the brand of your appliance is not in the list or

none of the codes given fits, we recommend the

automatic code search.

Your remote control finds the correct control settings

almost automatically in a few seconds:

1. Switch on the device to be controlled. For

example, a program number appears in the display

of your satellite receiver.

2. To start the code search, press and hold the

SET button for approx. 3 seconds. CODE SETUP

appears in the display. Confirm this function by

pressing OK.

3. DEV SEARCH then appears in the display.

Confirm this function by pressing OK.

– If DEV

SEARCH does not appear you can set the function with the

 or button.

4. Press the device button of the device to be

controlled, e.g. DVD and confirm the function by

pressing OK.

5. Then point the remote control at the device to

be controlled while the remote control emits a

different ON/OFF signal every 2 seconds. The

respective code number is shown in the display.

6. When your device reacts, press a few buttons

to determine whether you have found a suitable

code. If the code corresponds to your device, press

OK twice. SUCCESS appears in the display, then

you press the device button, e.g. DVD, to confirm

the entry. The setting for this device is now

completed.

7. If the code you have found does work at all or

not properly, press EXIT and DEV SEARCH

appears again. Then proceed again as described

under 3.

Please note: - You can reverse the search direction with the

 or  button if you have reacted too slowly to a response

from the device. – The Menu buttons cannot by used for

testing. - Before setting a code and performing the

subsequent test for recording or playback devices, please

insert a medium (tape, CD, cassette, DVD, etc.).- You can

interrupt code entry at any time by pressing EXIT.

Other settings

Setting the time

1 Press and hold SET for 3 seconds, then set

CONFIGURE with the  or  button. Confirm this

function by pressing OK.

2 TIME SETUP appears in the display. Confirm

this function by pressing OK.

3 Enter the time using the number buttons and

confirm with the OK button. Then press EXIT

several times to quit the setting mode.

Set priority volume control

With this function you can determine a device

exclusively for volume control, e.g. your audio

amplifier. Then the buttons VOL +, VOL – and

always control the amplifier, regardless of which

device you are controlling.

1 Press and hold SET for 3 seconds, then set

CONFIGURE with the  or  button. Confirm this

function by pressing OK

2 TIME SETUP appears in the display. Set VOL

LOCK with the  or  button. Confirm this function

by pressing OK.

3 Select the device button, e.g. AUX for the

amplifier and set priority=ON using the  or 

button. Confirm this function by pressing OK.

4 Then press EXIT several times to quit the

setting mode.

- You can cancel the priority setting using the same

procedure. Instead of ON, set OFF for all devices.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vivanco ur 850 lcd in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vivanco ur 850 lcd Manual

Product: