Manual Vivanco ur 810 (page 2 of 34) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish)

122761

Zoom out

Zoom in

1/34

UR 810 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135 2

Manual code search

1. Switch on the appliance to be

controlled. Program is running.

2. To prepare code search, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV, additionally

until the lamp (LED) lights constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the ON/OFF

(appliance on/off) button once. The lamp (LED)

blinks. – Except when searching for a TV code

you can also briefly press the yellow > (Play)

button and use the Play function to search.

Make sure that a tape, a DVD or a CD is

inserted in the tape deck, player or recorder.

5. Press the ON/OFF (appliance

on/off) or Play button repeatedly, approx. every

1,5 seconds, until the appliance, e.g. your DVD

player, reacts. - If you notice the reaction of

your appliance too late and the next code has

already been emitted you can go back by

pressing SET and then ON/OFF or Play again.

If your appliance has switched itself off you

must switch it back on again, e.g. on the

appliance or with the original remote control, to

continue searching. - When your appliance

reacts you can also try out other buttons

without interrupting the search. If some buttons

do not work properly, simply continue

searching with ON/OFF or Play.

6. When your appliance reacts

correctly, press the appliance button, e.g. TV,

and end the search. The lamp (LED) goes out.

- The UR 810 continues with the search at the

point where you interrupted it. When the end of

the code list is reached the search stops

automatically. The remote control blinks quickly

several times. The code last entered remains

stored. The search stops after approx. 30

seconds of inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be

controlled. A channel number, for example,

appears in the display of your satellite receiver.

2. To start the code search, press the

SET button, and then additionally the required

appliance button, e.g. TV, for more than 3

seconds until the lamp (LED) starts to blink.

3. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every 2

seconds.

4. When your appliance reacts, press

any button, except SET, to end the search. – If

you ended the search too late, continue to

search using the Manual Code Search (see

above).

5. Finally, test the control code setting

by trying to control, for example, your DVD

appliance. If it does not work correctly, please

try the code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVD, back on again if you wish

to continue searching.

Code identification

You can read off the 3-digit codes you have set

at any time:

1. Press the appliance button of the

appliance which code you want to read off, e.g.

TV.

2. Press the SET button and 1,2,3,

depending on the part of the code you want to

read off. For example, if you press SET+1 after

TV and the code 156 (in this example) has

been set, the lamp blinks once after SET+1 is

released to show that the hundred figure is 1.

All you have to do is count. The ten figure is

indicated after SET+2 is released, e.g. it blinks

5 times for the 5 in 156. The one figure is

indicated after SET+3 is released, e.g. it blinks

6 times for the 6 in 156.

Learning, Programming, of Missing Control

Functions

The LEARN function is used to supplement the

preprogrammed codes. The standard code

may provide most of functions needed, but you

may miss some key functions. Or you didn´t

find any functioning preprogrammed code for a

device. You can capture upto 100 key funtion

codes, max 40 per device. The last captured

function will overwrite the previous. learnt.

1 For learning of key codes you must use a

functioning orginal remote controller. Please

use fresh batteries for both remote controls.

2 Please point the original´s remote control

transmitter LED towards the receiver LED of

UR 810 (placed on top, same as transmitter

LED). Distance of LEDs between both remotes

shall be approximately 30mm and must be in

straight line of sight.

3 Press down and hold the Learn key and

press the device key (e.g. DVD) additionally

and then release the both pressed keys. Then

e.g. the DVD device key starts blinking

indicating that DVD key codes (functions) can

be captured.

4 Press and release the target key, that

you want to learn to (reprogram) (e.g.

POWER), the device button lights up.

5 Press and hold the source key on the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vivanco ur 810 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vivanco ur 810 Manual

Product: