769323
3
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 3
V20.2 UPDATES
Refer to the following changes that replace the equivalent information in the supplied installer guide.
4.4.2 Adding new wireless devices or wired sensors
Part B – Configuration
Zone Type List
No.
Zone Type
Description
25
Custom 1
A custom zone type that reports to private phone, and SMS numbers without activating any
sirens. This setting is configured to perimeter by default. To define the setting default, refer to
section 4.8.2 Custom Zone Types.
26
Custom 2
A custom zone type that reports to private phone, and SMS numbers without activating any
sirens. This setting is configured to perimeter by default. To define the setting default, refer to
section 4.8.2 Custom Zone Types.
4.4.7 Defining configuration defaults for "device settings"
The default configuration of the ‘VIEW ON DEMAND’ feature is ‘disabled’. To change the default configuration,
complete the following steps:
Changing VIEW ON DEMAND defaults
[1]
Enter the installer menu and select 02:ZONES/DEVICES
[2]
Select DEFINE DEFAULTS
[3]
Select MOTION SENSORS
[4]
Select VIEW ON DEMAND and choose the desired default setting from the list of options
Note: The selected default setting is marked with
Note: The new default affects only new motion cameras enrolled after the change is performed.
4.5.5 Configuring sirens functionality
In previous versions, an alarm that occurred in a single partition activated all sirens in the system. From
PowerMaster v20.2 onwards, you can configure the system so that the siren sounds only when an alarm is
triggered within the same partition.
Option
Configuration Instructions
48:SRN PER PRTN
This setting determines if the siren activates when an alarm occurs within the same partition.
Note: This option does not apply to sirens that are embedded in the panel or wired sirens that
are connected to expanders or PGMs.
If you set the siren to Enable, and an alarm is triggered in the same partition, the siren sound
and the exit and entry beeps activate.
Note: To silence a siren within a partition, you must have access privileges to that partition.
If set to Disable, the siren sound, as well as exit and entry beeps, are activated when an alarm
is triggered in any partition.
If you set the siren to Disable, and an alarm is triggered in any partition, the siren sound and the
exit and entry beeps activate.
Options: Disable (default) or Enable.
4.5.6 Configuring audible & visual user interface
Option
Configuration Instructions
56:SCREEN SAVER
With partition disabled
The screen saver option - when activated - replaces the status display on the control panel
with the words “SECURITY SYSTEM” if no key is pressed for more than 30 seconds.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info