652076
4
Zoom out
Zoom in
Previous page
1/16
Next page
4
Decoder auswertet legt man bei der Einstellung der Digi-
taladresse fest.
Der Adressumfang ist von dem Format abhängig, mit
dem der Decoder angesteuert wird.
Motorola-Format: 255 Adressen.
DCC- Format: 2048 Adressen.
Ansteuerung im Analogbetrieb
Den Viessmann Weichenantrieb können Sie auch in kon-
ventionell gesteuerten Modellbahnanlagen einsetzen.
Sie können ihn sowohl mit Wechselstrom- als auch mit
Gleichstrom betreiben.
Sobald Sie den Antrieb an Betriebsspannung anschlie-
ßen, erkennt der integrierte Decoder automatisch, ob er
analog oder digital angesteuert wird, und stellt den ent-
sprechenden Betriebsmodus ein.
Verhalten bei Überlastung
Bei Kurzschlüssen oder anderer Überlastung schaltet der
Weichenantrieb nach einer Zeit von ca. 2 Sekunden ab
und fährt in die Mittelstellung zurück.
Rückmeldung mit RailCom
®
RailCom
®
ist ein Zusatzprotokoll zur bidirektionalen Kom-
munikation in digitalen Modellbahnanlagen, die im DCC-
Format gesteuert werden. Es ermöglicht z. B. die Stel-
lungsrückmeldung der Weiche zur Digitalzentrale.
Das Versenden von RailCom-Messages ist nur in Anla-
gen möglich, in denen ein DCC-Signal an den Schienen
anliegt und seitens der Zentrale sowie der Booster eine
entsprechende Austastlücke im Datenstrom erzeugt wird.
Daher ist die Nutzung der RailCom-Funktion in einer rei-
nen Motorola-Umgebung nicht möglich.
Sofern der Decoder im Weichenantrieb die Austastlücke
registriert, sendet er nach einem erhaltenen Schaltbefehl
als Quittung die Sollstellung der Weiche zurück.
4. Einbau / Montage
Beachten Sie: Sowohl mechanische als auch
elektronische Bauteile im Inneren des Weichen-
antriebssindsehrempndlich.ArbeitenSiealso
sehr vorsichtig!
Sicherheitshinweis: Alle Anschluss- und Monta-
gearbeiten dürfen nur bei abgeschalteter Betriebs-
spannung durchgeführt werden.
Allgemeine Hinweise
Der Viessmann Weichenantrieb ist als Universalantrieb
für unterschiedliche Weichentypen konzipiert. Im Gehäu-
se ist die elektronische Steuerung inklusive Digitaldeco-
der sowie der Antriebsmotor inklusive mechanischem Teil
untergebracht (Gewindespindel, Abtriebshebel, Getriebe).
Der Weichenantrieb kann in jeder Lage montiert werden,
abhängig vom Weichentyp und Gleissystem.
Das Gehäuse ist systembedingt nicht hermetisch versie-
gelt. Durch die Öffnungen im Gehäuse können Kleinteile
wie Streumaterial etc. ins Innere gelangen und den An-
trieb zerstören.
Beachten Sie daher unbedingt die folgenden Hinweise:
Motorola-Format: 255 addresses.
DCC- Format: 2048 addresses.
Operation in analogue mode
The Viessmann switch motor can be used in conventional
model railroad layouts. You may use AC or DC power
supply for operation.
The integrated controller and decoder recognizes auto-
matically if there is AC or DC power supply or a digital
signal and adjusts itself to the correct mode of operation.
Overload protection
If the switch motor recognizes a short circuit or an over-
load, it switches off to protect itself against destruction. At
rst, the motor brings the drive to the mid-position. The
whole process of switching off may last up to 2 seconds.
Feedback with RailCom
®
RailCom
®
is a log for bi-directional communication in
digital model railway layouts controlled in DCC-format. It
allows e. g. the feedback of the address or the requested
position from the switch motor to the digital control unit.
Sending RailCom
®
messages is only possible in layouts
with a DCC signal on the rails and if the command station
and / or the booster(s) generate a cut-out in the digital
signal. That’s why it is not possible to use RailCom
®
in a
Motorola-system without DCC.
Whether the decoder of the switch motor registers the
RailCom cut-out, it sends back after an order it’s own
address and the requested position of the turnout to
acknowledge that it has receipt the order (so-called Rail-
Com broadcast datagramm).
4. Mounting and Connections
Notice:
Be careful with the switch motor. Mechanical and
as well as electronical components in the switch
motor are very sensitive.
Caution:
Make sure that the power supply is switched
off when you mount the device and connect the
wires!
General notice
The Viessmann switch motor is an universal drive for dif-
ferent types of turnouts. The case contains the electronic
control unit including the digital decoder and the drive unit
(motor, gear unit, thread and lever).
The switch motor may be mounted in every position. The
used mounting place and position of the switch motor de-
pends on the used track system and turnout type.
The case is not hermetically sealed due to it’s concept.
Small parts like ballast etc. may get into the casing
through the openings and destroy the switch motor!
Therefore pay attention to the following notices:
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 4554 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 4554 in the language / languages: English, German as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info