652081
5
Zoom out
Zoom in
Previous page
1/8
Next page
5
blau mit roter Markierung
blue with red marking
blau mit grüner Markierung
blue with green marking
gelb + Widerstand / Markierung
yellow with resistor or marker
gelb
yellow
braun (+Diode bei LED-Licht)
brown (+diode for LED lighting)
rot
red
rot
red
Signal Vr0 (Halt erwarten)
Signal Vr0 (expect stop)
Signal Vr1 (Fahrt erwarten)
Signal Vr1 (expect proceed)
gemeinsamer Mittelpunkt der Antriebsspulen
common pole for the drive coils
Licht
Light
Licht (Masse)
Light (ground)
Kontakt für Zugbeeinflussung
contact for train control
Kontakt für Zugbeeinflussung
contact for train control
blue with yellow marking
Signal Vr2 (Langsamfahrt erwarten)
Signal Vr2 (expect proceed slowly)
blau mit gelber Markierung
Fig. 5Abb. 5
dung) oder 5548 (mit Rückmeldung durch LEDs)
anschließen können. Schalter, Taster und Relais
anderer Hersteller können Sie auch verwenden.
Digitale Ansteuerung
Viessmann-Formsignale können auch von einem
Digitalsystem angesteuert werden (Abb. 7). Beim
Anschluss z. B. an den Viessmann-Magnetarti-
kel-Decoder 5211 (Märklin / Motorola) müssen Sie
darauf achten, dass neben den blauen Kabeln zur
Signalsteuerung auch das gelbe Kabel (ohne Mar-
kierung) für die Stromversorgung angeschlossen
ist. Zum digitalen Schalten eines dreibegriffigen
Signals werden 1½ Ausgangsgruppen eines Ma-
gnetartikeldecoders benötigt. Die nicht benötigte
Ausgangsbuchse kann für ein weiteres dreibegrif-
figes Signal verwendet werden (zusammen mit
einer anderen Ausgangsgruppe) oder für ein Ent-
kupplungsgleis.
Viessmann-Formsignale mit 2 Antrieben benöti-
gen positive Schaltimpulse. Daher kann man die
Signale nicht ohne weiteres mit allen Magnetar-
tikeldecodern (z. B. von Lenz, Trix etc.) schalten,
da diese Decoder negative Schaltimpulse liefern.
Von Viessmann gibt es daher für alle Digitalsys-
teme Decoder, welche positive Schaltimpulse lie-
fern!
Der 5211 (4-fach) ist kompatibel zum Märklin / Mo-
torola und Märklin-Systems-Format. Der 5212
feedback or 5548 with feedback).
Power is supplied via the brown wire and the two
yellow wires. The blue wires with the coloured
markings are connected to contacts (single mo-
mentary switches, track contacts, automatic track
switches, control panel), which in turn are wired to
the brown lead ( = “ground”). Never supply power
to more than one blue wire at the same time.
The red wires are used to connect the insulated
track section to the signal contacts (train control).
Digital Control
The semaphore home signals can also be oper-
ated with a digital system. Refer to figure 7 on the
following page for the correct wiring.
Simply connect the wires to a digital decoder
(e.g. Viessmann 5211 for Märklin / Motorola for-
mat, 5212 for the NMRA DCC format or 5260 for
SELECTRIX
®
).
Viessmann-semaphores with two drive units need
positive switching impulses. Therefore you cannot
use any decoder (e. g. by Lenz, Trix etc.) because
they use negative impulses.
Viessmann delivers decoders for all digital sys-
tems and standards:
5211: compatible with the Märklin / Motorola and
Märklin-Systems format.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 4520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 4520 in the language / languages: English, German as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Viessmann 4520

Viessmann 4520 User Manual - Dutch, French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info