785218
1
Zoom out
Zoom in
Previous page
1/6
Next page
Page 1 of 6
Cyrix-i 12/24-400
Cyrix-i 24/48-400
Intelligent battery combiner
ENGLISH
No voltage loss
The Cyrix-i 400 battery combiner is a microprocessor controlled heavy duty
contactor that automatically connects batteries in parallel when one battery has
reached a preset voltage (indicating that the battery is being charged), and
disconnects when the voltage decreases below float level (indicating that one or
both batteries are being discharged).
Cyrix battery combiners are an excellent replacement for diode isolators. The main
advantage is that there is virtually no voltage loss so that the output voltage of
alternators or battery chargers does not need to be increased.
Prioritising the starter battery
In a typical setup the alternator is directly connected to the starter battery. The
accessory battery, and possibly also a bow thruster and other batteries are each
connected to the starter battery by Cyrix battery combiners. When a Cyrix senses
that the starter battery has reached it’s connect voltage it will engage, to allow for
parallel charging of the other batteries.
Bidirectional voltage sensing
The Cyrix senses the voltage of both connected batteries. It will therefore also
engage if for example the accessory battery is being charged by a battery charger.
Intelligent battery monitoring
Four different connect/disconnect profiles can be selected to suit local
requirements.
12/24Volt and 24/48Volt auto ranging
The Cyrix-i 12/24 will automatically adjust to a 12V or 24V system.
The Cyrix-i 24/48 will automatically adjust to a 24V or 48V system.
Bicolor LED status indicator
Red: contactor open
Red/green: timer
Green: contactor closed
Microswitch for for remote switch status monitoring
Installation (see figure below)
1. The Cyrix can only be used in installations with a negative common.
2. Disconnect the minus of both batteries.
3. Place the Cyrix closest to the smallest battery (in general the starter
battery).
4. Connect the plus of the batteries to the brass bolts of the Cyrix, (battery
1 and battery 2). Install a fuse in series (see fig). The fuse should be
sized in accordance with the wire cross section used, but not exceed
400A.
5. Connect the common battery negative to “battery –“ of the Cyrix and
reconnect the minus of both batteries.
6. An emergency start push button can be wired to the “start assist”
connection if required. The relay will engage during 30 seconds after the
start assist” has been momentarily connected to the battery plus.
Alternatively, a parallel connect switch can be used to engage the relay
as long as the switch remains closed.
7. An auxiliary micro switch is available for remote monitoring.
Cyrix-i 12/24-400
Cyrix-i 24/48-400
Intelligente accuscheider
NEDERLANDS
Geen spanningsverlies
De Cyrix-i 400 bestaat uit een microprocessor gestuurd power relais dat accu’s
automatisch van elkaar loskoppelt wanneer de spanning daalt tot onder een
bepaalde waarde (een teken dat de accu’s niet geladen worden), en weer parallel
schakelt wanneer de spanning over één van de accu’s stijgt tot boven een bepaalde
waarde (een teken dat de accu geladen wordt).
De Cyrix accuscheider is een uitstekend alternatief voor diode of FET laadstroom
verdelers. Het spanningsverlies is namelijk praktisch nihil.
Voorrang voor de startaccu
De startaccu mag nooit leeg raken. Het is daarom gebruikelijk om de dynamo op de
startaccu aan te sluiten. Andere accu’s, zoals de accessoire accu, en (in een boot)
mogelijk ook de boegschroef accu kunnen vervolgens met een Cyrix accuscheider
op de startaccu aangesloten worden. De Cyrix accuscheiders zorgen er dan voor
dat alle accu’s parallel geschakeld worden zodra de spanning van de startaccu
voldoende gestegen is.
Bidirectioneel
De Cyrix meet de spanning over alle twee de aangesloten accu’s. De accu’s zullen
dus ook parallel geschakeld worden wanneer de accessoire accu geladen wordt,
bijvoorbeeld met een acculader.
Intelligente accuspanning bewaking om herhaald schakelen te voorkomen
Er kunnen bovendien vier verschillend schakel profielen ingesteld worden.
Twee modellen, geschikt voor 12V/24V, of 24/48V accuspanning
De Cyrix-i kiest automatisch de juiste systeem spanning.
Twee kleuren LED voor status indicatie
Rood: open
Rood/groen: timer loopt
Groen: gesloten
Microswitch voor open/gesloten signalering op afstand
Installatie (zie schema)
1. De Cyrix is alleen geschikt voor installaties met een negatieve massa.
2. Maak de min polen van beide accu’s los.
3. Plaats de Cyrix dicht in de buurt van de kleinste accu (iha de startaccu).
4. Verbind de plus polen van de 2 accu’s aan de bout aansluitingen van de
Cyrix (battery 1 and battery 2). Installeer ook een serie zekering (zie fig).
De waarde van de zekering moet afgestemd zijn op de gebruikte
draaddoorsnede en mag niet meer dan 400A bedragen.
5. Verbind de min aansluiting “battery –“ van de Cyrix en sluit de minnen
van de accu’s weer aan.
6. Noodstart drukknop. Indien pen “start assist” kort met de accu plus
verbonden wordt zal het relais gedurende 30 seconden sluiten. Indien
een schakelaar gebruikt wordt ipv een drukknop zal het relais gesloten
blijven zolang de schakelaar gesloten is.
7. Gebruik indien gewenst de microswitch voor open/gesloten signalering
op afstand
Model
Cyrix
-
i 12/24
-
400
Cyrix-i 24/48-400
Continuous current 400A
Peak current 2000A during 1 second
Input voltage 12/24V model
Input voltage 24/48V model
-
36VDC
18-72VDC
Connect/disconnect profiles
See table
Over voltage disconnect 16V / 32 / 64V
Current consumption when open 4 mA
Emergency start Yes, 30s
Microswitch for remote monitoring
Yes
Status indication Bicolor LED
Model
Cyrix
-
i 12/24
-
400
Cyrix-i 24/48-400
Continu stroom 400A
Piek stroom
2000A gedurende 1 seconde
Ingangsspanning 12/24V model
Ingangsspanning 24/48V model
-
36VDC
18-72VDC
Schakel profielen Zie tabel
Afschakelen bij overspanning 16V / 32 / 64V
Stroomverbruik (open) 4 mA
Start Assist Ja, 30s
Microswitch voor status indicatie
Ja
Status indicatie op de Cyrix
Twee kleuren LED
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Cyrix-i combiner relais 12 24V-400A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Cyrix-i combiner relais 12 24V-400A in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info