474330
6
Zoom out
Zoom in
Previous page
1/9
Next page
MONTAGE DES MAGNETS, DES SENSORS UND DER HALTERUNG
Wir empfehlen die Montage Deines C-06 beginnend mit der Montage des Sensors
an der Gabel und dann hinaufgehend zur Halterung am Lenker.
SCHRITT 1
Montiere den neuen Vetta S-2 universal sensor (patentiert) mit dem mitgelieferten
Kabelbinder an der linken Gabelscheide vorerst nur leicht (so daß Du die Position
noch verändern kannst). Der Sensor kann an jedem Punkt der Gabel montiert
werden, wir empfehlen jedoch die Montage an der Rückseite und ziemlich weit
oben auf der Gabel. Das schützt den Sensor vor Beschädigungen durch Steine,
äste und andere Objekte.
SCHRITT 2
Montiere den Speichenmagnet wieder vorerst nur leicht auf einer Speiche auf der
linken Seite des Vorderrads. Justiere die Magnet und Sensorposition durch
Verrutschen beider Teile bis Du eine Position erreichst, bei der der Sensor so
hoch wie möglich auf der Gabelscheide montiert ist und gleichzeitig der
notwendige Abstand vom Sensor zum Speichenmagneten (1-2mm) gewährleistet
Sensor
Kabelbinder
Pfeil
Gabelscheide
Magnet
1-2mm
Kabelverlegung
!
!
BEACHTE: Der Magnet soll 1-2mm Abstand vom Sensor haben, und die
Oberkante des Magneten soll nicht höher als die Oberkante des schmalen Pfeiles am
Sensor sein.
SCHRITT 3
Verlege das Sensorkabel auf der Rückseite der Gabel mit Isolierband.
ACHTUNG Verwende keine Kabelbinder um das Sensorkabel zu fixieren, da
dadurch das Kabel durchgeschnitten oder abgebrochen werden könnte.
ACHTUNG Vergewissere Dich bei der Verlegung des Kabels, daß Du genug
Reserve hast um das Vorderrad in beide Richtungen voll einschlagen zu können
und ebenfalls genug Kabellänge hast, daß die Federgabel einwandfrei arbeiten
kann (falls welchen benützt wird).
SCHRITT 4
Wickle das übrige Kabel vorsichtig um die Hülle des vorderen Bremskabels und
sichere es wenn nötig mit Isolierkabel. Wenn Du fertig bist solltest Du noch genug
Länge haben, um die Computerbefestigung am Lenker befestigen zu können.
Prüfe noch einmal ob all das übrige Kabel mit Isolierband befestigt oder um das
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VETTA C06 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VETTA C06 in the language / languages: German as an attachment in your email.

The manual is 0,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info