514915
3
Zoom out
Zoom in
Previous page
1/20
Next page
DX2 Operator control
vD - 2013-04
2
1.1. DX2 without LCD screen
Press the "ON/OFF" button (1). The charge indicator (2), which also indicates the batteries' charge
level, lights up for a moment. If all the lights come on, the batteries are sufficiently charged. If the lights
do not all come on, you must adjust your driving activities to suit the low capacity of the batteries. If the
battery charger display lights do not come on, check the plug connections of the electronic system.
Now select the driving program you want by pressing the speed switch (3), (-) symbol to go slower and
(+) symbol to go faster.
The selected speed is showed with the speed indicator (4). If you have any special needs, you can
ask your dealer to enter a personalised driving program.
To set the wheelchair in motion, push the joystick forwards slowly. The speed will increase when you
push the joystick further forwards. If you want to turn left or right, simply push the joystick in the
desired direction. To reverse, pull the joystick backwards from the central position.
L
Note that, when pressing the "ON/OFF" button, the joystick stays in the central position for at
least two seconds. It is programmed this way for technical and safety reasons, to prevent the
joystick being pushed at the same time as the wheelchair is being switched on. If both
processes are activated at the same time, the steering unit locks itself and can only become
operational again after being switched off completely.
Press the “Left indicator” (10) or “Right indicator” (11) buttons to signal a change in your driving
direction. The driving lights are switched on or off by pressing the “Lights” (15) button. You can sound
an acoustic warning signal with the “Horn” (5) button. The hazard warning lights, used in critical
situations, can be switched on or off by pressing the “Hazard warning lights” (14) button.
To brake while driving, simply push the joystick to its central position. Move the joystick slowly for
gradual braking. Simply release the lever for a quick stop; the wheelchair will then stop as quickly as
possible.
To activate the back adjuster, select button (13) until the corresponding number for the backrest
adjustment actuator lights up, and you can then use the joystick to tilt the back in the direction you
want.
To activate the seat incliner, select button (13) until the corresponding number for the seat adjustment
actuator lights up, and you can then use the joystick to incline the seat in the direction you want.
Turn wheelchair On/Off
In case of an emergency, you can use the On/off button to turn your wheelchair off.
Turn the power on:
Press the On/Off button. All LEDs of the battery indicator turn on simultaneously
and the fault indicator flash twice.
If the wheelchair is turned on while the joystick is out of neutral, an fault will be displayed on the
battery charge indicator (the five drive profile LEDs flash continuously and the chair will not drive).
Release the joystick back to neutral and the fault will disappear. If the joystick is not released
back to neutral (centre) within 4 seconds, the fault becomes a Module fault (the drive profile LEDs
+ fault indicator are flashing). To clear this fault, turn the DX system off and then turn it back on.
Turn the power off:
Press the On/Off button. All LED's will goe out. If the ON/OFF button is pressed
while driving the wheelchair perform an emergency stop and it turns off.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermeiren Controleunit D2X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermeiren Controleunit D2X in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermeiren Controleunit D2X

Vermeiren Controleunit D2X User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info