482683
2
Zoom out
Zoom in
Previous page
1/15
Next page
Sea level pressure setting
After battery/adapter installation, the monitor will enter sea level pressure setting mode directly and the
pressure reading will flash. Press “ or to set the sea level pressure value. Press PRESSURE to
confirm the setting and exit. This allows the unit to provide a more accurate weather forecast &
pressure reading.
You can also set the sea level pressure any time after the installation is completed. For more
information, see WEATHER FORECAST & BAROMETRIC PRESSURE section.
Note: you may obtain the current sea level pressure from the weather web site for your locate area.
2. Selecting a location for the anemometer
Select a mounting location for the anemometer that is:
- Outdoors, not blocked on top or sides, so wind can freely reach the anemometer
- Within 50 meter (164 feet) open area from the monitor. Reduce distance if obstacles is between
the anemometer & the monitor
The best location for the anemometer is usually mounted on a mast in an open area where wind is not
blocked on top or sides, or above roof level on the building where the monitor is located.
Testing the effective transmission range
Before mounting the anemometer, measure the distance between the monitor & anemometer and be
sure it is within the effective transmission range. It is recommended to perform a simple RF
transmission test before mounting.
1) Place the monitor in your selected indoor location and install adapter & batteries (see Battery &
adapter installation for the monitor section above)
2) Place the anemometer horizontally in your selected outdoor location. Loosen the screws on the
battery door with a small Phillips screwdriver and open the battery door. Insert 2 pieces of AA
batteries according to the polarity indicated. Close the battery door and tighten the screws.
3) Hold CHANNEL/SEARCH button on the monitor for 3 seconds and the wind speed & direction
icons will flash on the display. The monitor is now searching for all remote sensors for 2 minutes.
4) If valid wind direction and wind speed readings are shown on the monitor within 2 minutes, the RF
transmission is successful and the anemometer & monitor are within the effective transmission.
If above readings are not shown after 2 minutes of searching, the transmission is failed.
Shorten the distance between the anemometer & monitor. Reset the anemometer by removing all
batteries from the anemometer & wait for 10 seconds before re-installing the batteries again.
Repeat step 3 & 4 until the transmission is successful.
5) Remove all batteries from the anemometer before mounting and calibration.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ventus W155 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ventus W155 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ventus W155

Ventus W155 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info