756788
7
Zoom out
Zoom in
Previous page
1/9
Next page
POWX4203 EN
Copyright © 2021 VARO P a g e | 7 www.varo.com
battery/on-board vehicle power supply or a connected consumer. It is
imperative that you make sure the polarity is correct when you connect up.
Observe the maximum power consumption of the consumer.
NOTE: The direct voltage which is provided (shown in the display) is load-dependent and
without load it is approx. 14.5 V. This function can be used for consumers which are
operated from a vehicle’s cigarette lighter. Refer to and observe the operating manual for
your 12 V consumer.
7.5 Charging the battery
Release or remove the battery stoppers (if fitted) from the battery.
Check the acid level in the battery. If necessary, top up the battery with distilled water (if
possible). Battery acid is aggressive. Rinse off any acid splashes thoroughly with lots of
water and seek medical advice if necessary.
First connect the red charging cable to the positive pole of the battery.
Then connect the black charging cable to the bodywork of the vehicle away from the
battery and the petrol pipe.
Warning! Under normal circumstances the negative battery pole is connected to the
bodywork and you proceed as described above. In exceptional cases it is be possible that
the positive battery pole is connected to the bodywork (positive earthing). In this case,
connect the black charger cable to the negative pole on the battery. Then connect the red
charger cable to the bodywork at a point away from the battery and the petrol pipe.
After the battery has been connected to the charger, you can connect the charger to a
socket. You can now change the settings (see 7.4).
Important! Charging may create dangerous explosive gas and therefore you should avoid
spark formation and naked flames whilst the battery is charging. There is a risk of
explosion! It is essential that you ventilate the rooms well.
When “Ful” appears in the LCD display and all increments (K) are lit, charging has been
completed. The charger holds the battery at 95% 100% available battery capacity using
pulsed charging. If the charger shows this after just a few minutes, this indicates that the
battery capacity is low. The battery needs replacing.
7.6 Calculate the charging time (fig.2)
The charging time depends on the charge status of the battery. If the battery is fully
discharged, the approximate charging time up to approx. 80% charged can be calculated
using the following formula:
Battery capacity in Ah
Charging time/h =
Amp. (charging current)
The charging current should be 1/10 to 1/6 of the battery capacity.
7.7 Fault indicator (G)
The fault indicator will flash in the following cases:
If the voltage of the battery is less than 3.5V or more than 15 V. The battery is either
unsuitable for charging or is defective. It is also possible that other battery errors or faults
can mean that the battery cannot be charged.
If the terminal clamps are connected to the battery terminals with the wrong polarity. The
protection against swapped poles ensures that the battery and charger do not get
damaged. Remove the charger from the battery and start the charging process from the
beginning again. CAUTION! Protection against swapped poles is not available when the
SUPPLY program is used.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX4203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX4203 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX4203

Varo POWX4203 User Manual - German - 10 pages

Varo POWX4203 User Manual - Dutch - 9 pages

Varo POWX4203 User Manual - French - 10 pages

Varo POWX4203 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info