701807
12
Zoom out
Zoom in
Previous page
1/15
Next page
POWX155 EN
Copyright © 2020 VARO P a g e | 12 www.varo.com
10 CLEANING AND MAINTENANCE
Attention! Before performing any work on the equipment, pull the power
plug.
10.1 Cleaning
Always wear sturdy gloves when handling or changing bits and cutters as they can be very
sharp.
Wear safety glasses to protect your eyes whilst cleaning.
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
10.2 Lubrication
Turn the drill shaft to the maximum drilling depth once per 3 months and grease it slightly
with oil.
10.3 Spindle play (Fig. 18)
Locate the spindle play adjustment set screw.
Loosen the lock nut and finger-tighten the grub screw.
Hold the grub screw into position with a hex key and tighten the lock nut (Fig. 18).
10.4 General inspection (Fig. 19)
Regularly check that all the fixing screws are tight. They may vibrate loose over time.
If the supply cord requires replacing, the task must be carried out by the manufacturer, the
manufacturers agent, or an authorized service centre to avoid a safety hazard (Fig. 19).
10.5 Power cord
If the power cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a safety hazard.
11 TROUBLE SHOOTING
Suspected malfunctions are often due to causes that the users can fix themselves. Therefor
check the product using this section. In most cases the problem can be solved quickly.
Problem
Possible cause
Solution
1. Noisy operation
1.1 Incorrect belt tension
1.2 Loose spindle pulley
1.3 Loose motor pulley
1.1 Adjust tension
1.2 Tighten the pulley insert nut
1.3 Tighten the screws
2. Drill bit gets
excessively hot
2.1 Incorrect speed
2.2 Chips not coming out of
hole
2.3 Dull drill bit
2.4 Feeding too slow
2.5 Drill bit not being allowed
to cool down or not
lubricated in use
2.1 Adjust the speed
2.2 Retract drill bit frequently to
clear chips
2.3 Resharpen drill bit
2.4 Feed fast enough, allow drill
bit to cut
2.5 Lubricate drill bit when
cutting. Follow S2 duty cycle
time
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX155 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX155 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX155

Varo POWX155 Additional guide - English - 5 pages

Varo POWX155 User Manual - German - 17 pages

Varo POWX155 User Manual - Dutch - 16 pages

Varo POWX155 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info