622522

Varo MOTSA19EL Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
MOTSA10EL, 12EL, 15EL & 19EL EN
Copyright © 2012 VARO NV P a g e | 1 www.varo.com
OPERATION INSTRUCTIONS
CAUTION: Do not keep the keys in the safe.
1 OPEN THE SAFE FOR THE FIRST TIME
To open the safe for the first time, remove the small plastic cover on the front panel, insert the
key into the lock and turn it counter-clockwise, at the same time, turn the knob clockwise and
open the door.
2 INSTALLING THE BATTERIES.
The safe requires 4× size ‘AA’ (1.5V/R06) batteries. Remove the battery cover and install the
batteries into the compartment. Ensuring the batteries are fitted with the correct corresponding
polarity. The display will scan the status of the electronic lock system automatically. If it is in
order, the display will show ‘good’.
3 OPENING THE SAFE AFTER INSTALLING BATTERIES
To open the door of the safe, press the button ‘START’, the display on the panel will show ‘----
----’, then input one of the two sets of factory-preset codes:
0,0,0,0 (user code) or 8,8,8,8 (master code) immediately and confirm by pressing the button
‘START’. You will hear a musical sound with the display showing ‘OPEN’ and open the safe
using the knob within approximately 4 seconds.
4 PROGRAMMING THE CODE
NOTICE: The safe can be programmed with two sets of codes. For your safety, after
opening the safe and installing the batteries, you should program two sets of your new
codes to take the place of two sets of factory-preset codes.
4.1 Programming the user code
A. With the door of the safe open, press the red button (located on the inside of the door near
the hinge) and the display will show ‘SET CodE’.
B. Now press from 3 to 8 numbers that you wish to use as a new user code, and confirm by
pressing the button ‘START’. After hearing a musical sound, the display will show ‘IN’ and your
inputting numbers. It means that the new user code is confirmed.
4.2 Programming the master code
A. Press the red button then press the button ‘START’. The display will show ‘oLd CodE’.
B. Now input the original master code (factory preset code: 8,8,8,8) and press the button
‘START’. The display will show ‘SET’. Now press from 3 to 8 numbers that you wish to use as
a new master code, and confirm by pressing the button ‘START’. The display will show ‘rE-
InPUT’.
C. Now enter your inputting numbers again and confirm by pressing the button ‘START’. After
hearing a musical sound, the display will show ‘IN’ and your inputting numbers. It means that
the new master code is confirmed.
If you or an intruder uses the incorrect group of numbers, you will hear a beep with the display
showing ‘Error’ and it will not open. If the incorrect combination code is used 4 times
consecutively, the display will show ‘Error’, the buzzer will sound for approximately 3 minutes.
The correct code cannot be entered until after this 3 minutes delay. The override key can
however be used to open the door during this three minutes. If the key is used to open the
door, the buzzer can be cleared by pressing the red button.
If you do not want the display to show your codes or numbers when you open the safe, just
press the button ‘START’ twice at the first time of pressing and other steps are the same.
1


Need help? Post your question in this forum.

Forumrules
1

Forum

varo-motsa19el

Reset search

  • Hi , I lost my password and I dont know how to reset it and open it.
    I am able to reach the red button inside the safe but I am not able to enter a new password. Can you help me please
    Varo MOTSA19EL Submitted on 9-12-2019 at 23:00

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo MOTSA19EL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo MOTSA19EL in the language / languages: English as an attachment in your email.

The manual is 0,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo MOTSA19EL

Varo MOTSA19EL User Manual - German - 2 pages

Varo MOTSA19EL User Manual - Dutch - 2 pages

Varo MOTSA19EL User Manual - French - 2 pages

Varo MOTSA19EL User Manual - Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info