557924

UPM WT440H Manual

2
Zoom out
Zoom in
Previous page
1/6
Next page
MOONPHA SE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
1
1
1
1
1
2
2
2
3
3
*
*
4
4
2
3
4
SETTING UP THE RECEIVER
WIRELESS TRANSMISSION
WIRELESS TRANSMISSION
Automatic Learn Function:
Manual Learn Function (Remote Signal Search):
The learn function executes automatically and runs for approximately
3 minutes when batteries are first installed in the receiver.
Press and hold for 3 seconds to start.CHN
If a new remote transmitter is added or if signal is lost (outdoor
readout on the receiver is blinking), the learn function must be
executed again.
Within these 3 minutes, the receiver will pick up the temperature and
humidity signals from remote transmitter and display the reading.
Unit will beep to indicate that the learn function has started.
Channel symbol will blink and unit will continue to beep as each
remote transmitter is detected.
Within 3 minutes, the temperature and humidity reading of the remote
transmitter will display on the receiver.
TEMPERATURE ALARM TEMPERATURE ALARM
MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
MOONPHA SE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
2
Synchronized
Remove battery cover
batteries into compartment,
observing proper polarity; then
replace cover
Insert
1
2
3
2 AA size batteries (included)
3
3
1
1
4
4
2
2
*
*
3
3
2
1
WIRELESS TRANSMISSION
For optimal performance:
Place the receiver and remote transmitter side by side about 1 metre
apart, and allow the receiver and remote transmitter to synchronize
for 10 minutes before you place the remote transmitter outdoors.
Environmental factors and signals from other household devices, such
as remote entry controls, security systems, and computers, may
interfere with the wireless transmission of this product and cause
temporary reception loss. This is normal and does not affect the general
performance of this product. Stable reception will resume once the
interference ends.
The remote transmitter should be placed in a dry shaded area.
NOTE: Fog and mist will not harm the remote transmitter but
direct rain must be avoided.
Mount the remote transmitter upright avoiding metallic objects
and frames, such as window sills. Verify that there are no obstacles
like a transmission tower or steep hill that can cause interference
and blockage between the remote transmitter and receiver.
Place the receiver unit at least 2 metres away from any electrical
devices, such as your television set, computer, cordless phone, or any
radio controlled equipment.
Replace unit(s) with fresh batteries when the Low Battery Indicator
lights up. Refer to the LOW BATTERY INDICATION section.
You may need to reposition the remote transmitter to a different
location and/or closer to the receiver for the best transmission.
The is an ideal feature to be used for greenhouses
and wine cellars, or any place that you require controlled temperature.
Once activated, the temperature alarm would sound when the room gets
too warm or too cold depending on your settings.
temperature alarm
You can set both an upper and lower temperature alarm for the local
temperature (main receiver unit) and/or for each of the remote
(outdoor) channels of 1 to 4.
Scroll to the Upper Temperature Alarm Setting mode by pressing .
You should see the symbol and dotted lines ( ) or pre-existing
setting blink.
MODE
---
Scroll to the Lower Temperature Alarm Setting mode by pressing .
You should see the symbol and dotted lines ( ) or pre-existing
setting blink.
MODE
---
Select the desired channel, local or remote channels (1 to 4) using .CHN
Select the desired channel, local or remote channels (1 to 4) using .CHN
Press to finish; or rMODE epeat steps for all
other channels if desired.
Press to finish; or rMODE epeat steps for all
other channels if desired.
NOTE: In the normal clock display, when either the upper or lower
temperature alarm has been set for a particular channel, the or
symbol will show up solid on the LCD screen when that channel is displayed.
Press or key to set the desired value for the upper temperature limit.+-
Press or key to set the desired value for the lower temperature limit.+-
To disable the particular alarm, press .
The dotted lines ( ) would reappear to indicate
that the alarm has been disabled.
ALARM
---
To disable the particular alarm, press .
The dotted lines ( ) would reappear to indicate
that the alarm has been disabled.
ALARM
---
WD633 Receiver
LOW BATTERY INDICATION
Replace the batteries when the Low Battery Indication ( ) lights up on
the middle-left portion of the LCD screen on the WD633 receiver.
NOTE: After replacing the batteries, you will need to perform the Setup and
Learn Function procedures again. Refer to the SETTING UP THE
TRANSMITTER/RECEIVER and WIRELESS TRANSMISSION sections.
A
A
C
Setting the Upper Temperature Alarm
Setting the Lower Temperature Alarm
UPPER TEMPERATURE LIMIT: warmIf the temperature gets too
and reaches the upper temperature limit, the alarm would sound.
LOWER TEMPERATURE LIMIT: coldIf the temperature gets too
and reaches the lower temperature limit, the alarm would sound.
MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
When the Temperature Alarm Sounds
The temperature alarm will sound when the actual temperature has
reached (or exceeded) the upper or lower temperature limit.
The temperature alarm has a distinctive tone different to that of
Alarm 1 or Alarm 2.
or symbol and temperature limit will blink
Press ANY key to stop the temperature alarm. Or without interruption,
the temperature alarm will automatically stop after one minute.
PAGE 4
PAGE 13
PAGE 5
PAGE 14
PAGE 6
PAGE 15
1
1
1
1
4
WT440H Remote Transmitter
Replace the batteries when the Low Battery Indication lights up on
the bottom-left corner of the LCD screen on the WT440H transmitter.
When the batteries are low on a transmitter, a Low Battery Indication
( ) will also light up on the bottom-left corner of the LCD screen on
the WD633 receiver for that particular channel.
B
C
1
B
2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for UPM WT440H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of UPM WT440H in the language / languages: English, French as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info