Manual UPM WS222 (page 1 of 4) (English, French)

557947

Zoom out

Zoom in

1/4

BUTTON PLACEMENT

MIN/-/MIN: shows minimum temperature;

adjusts clock, alarm, and temperature alarm

values

C/F: changes House Code and Channel Code;

selects °C or °F

SET: activates SET function

Battery Compartment

LCD Screen

ALARM /(°C/°F): toggles between °C and °F,

12 and 24 hour format, and alarm ON and OFF;

disables temperature alarms

CHN: scrolls through local and remote

channels (1 to 4);

HOUR/+/MAX: shows maximum temperature;

adjusts clock, alarm, and temperature alarm

values

MODE/SNOOZE: scrolls through the

clock, alarm, and (upper & lower) temperature

alarm modes; snooze for alarm

GETTING STARTED

Remove battery cover

Set up the transmitter(s) setting up the receiverbefore

Remove battery cover

2 AA size batteries (included)

setting up the transmitter

The temperature will appear on the LCD screen

House code will blink for 8 seconds

Select House code (1-15) by pressing C/F

Press SET

Channel code will blink for 8 seconds

Select Channel code (1-4) by pressing C/F

* If you have multiple transmitters for a single receiver,

set each transmitter to the House codesame

* If you have multiple transmitters for a single receiver,

set each transmitter to a Channel codedifferent

Min and Max Temperature

Temperature Trend

WS222 Receiver

WT440 Remote Transmitter

TEMPERATURE DISPLAY

The trend indicator shows the trend of the temperature

in the past half-hour interval.

Example:

The following indicates that the

temperature is rising.

Arrow Indicator

Rising

Steady

Falling

Trend

WS222 + WT440

Wireless Weather Station

OWNER’S

MANUAL

setting up the receiver

Synchronized!!!

WIRELESS TRANSMISSION

Automatic Learn Function:

Manual Learn Function (Remote Signal Search):

The learn function starts automatically and runs for approximately

3 minutes when batteries are first installed in the receiver.

Press and hold for

3 seconds to start.

CHN

If a new remote transmitter is added or if signal is lost (outdoor readout

on the receiver is blinking), the learn function must be executed again.

Within the 3 minutes, the receiver will pick up the temperature

signal from the remote transmitter and display the reading.

Unit will beep to indicate that

learn function has started.

Channel symbol will blink and

unit will continue to beep as

each remote transmitter is detected.

Within 3 minutes, the temperature reading of the remote transmitter

will display on the receiver.

WS222 receiver

WT440 transmitter

Battery Cover

Wall Mount Bracket & Table Stand

SET

C/F

.5V

Insert batteries into compartment,

observing proper polarity

Insert batteries into compartment,

observing proper polarity; replace cover

Select temperature display in C or F by pressing C/F

°°

Replace battery cover

Congratulations on your purchase of this

weather station set, WS222+WT440.

Please take the time to read and

understand this manual so you can begin

to enjoy the convenience and features this

product has to offer.

Main Display Unit WS222:

* clock and alarm clock function

* local temperature display

* receives and displays temperature

readings from up to 4 remote

transmitters via RF technology of 433MHz

* minimum/maximum temperature memory

* temperature trend indicator

* local/remote temperature alarms

* day/night icon

* user-selectable C or F

* battery type:2xAA

°°

FEATURES

Remote Transmitter WT440:

* drip-proof design with LCD screen

* temperature display in user-selectable

Cor F

* transmission range: up to 40 metres in

open area

* table stand or wall mountable

* battery type:2xAA

°°

SET

C/F

.5V

Press intheClockmodetodisplay

the minimum temperature

The MIN symbol will appear.

MIN

To return to normal temperature

display, press again.MIN

To return to normal temperature

display, press again.MAX

Press inClockmodetodisplay

the maximum temperature.

The MAX symbol will appear.

MAX

NOTE: Min/Max readings are automatically cleared daily at 00:00

Press to view the minimum or maximum temperatures of the

local and remote channels 1 to 4.

CHN

LOW BATTERY INDICATION

Replace the batteries when the Low Battery Indication lights up on

the LCD screen by the local (indoor) temperature display.

NOTE: After replacing the batteries, you will need to perform the Setup

and Learn Function procedures again. Refer to the GETTING STARTED

and WIRELESS TRANSMISSION sections.

Replace the batteries when the Low Battery Indication lights up on

the bottom-left corner of the LCD screen on the WT440 transmitter.

When the batteries are low on a transmitter, a Low Battery Indication

willalsolightupontheLCDscreenoftheWS222receiverforthat

particular channel.

MINIMUM

MAXIMUM

TEMPERATURE ALARM

The is an ideal feature to be used for greenhouses

and wine cellars, or any place that you require controlled temperature.

Once activated, the temperature alarm would sound when the room gets

too warm or too cold depending on your settings.

temperature alarm

You can set both an upper and lower temperature alarm for the local

temperature (main receiver unit) and/or for each of the remote

(outdoor) channels of 1 to 4.

Scroll to the Upper Temperature Alarm Setting mode by pressing .

You should see the symbol and dotted lines ( ) or pre-existing

setting blink.

MODE

---

Select the desired channel, local or remote channels (1 to 4) using .CHN

Press to finish; or rMODE epeat steps for all

other channels if desired.

Press or key to set the desired value for the upper temperature limit.+-

To disable the particular alarm, press .

The dotted lines ( ) would reappear to indicate

that the alarm has been disabled.

ALARM

---

Setting the Upper Temperature Alarm

UPPER TEMPERATURE LIMIT: warmIf the temperature gets too

and reaches the upper temperature limit, the alarm would sound.

LOWER TEMPERATURE LIMIT: coldIf the temperature gets too

and reaches the lower temperature limit, the alarm would sound.

TEMPERATURE ALARM

Scroll to the Lower Temperature Alarm Setting mode by pressing .

You should see the symbol and dotted lines ( ) or pre-existing

setting blink.

MODE

---

Select the desired channel, local or remote channels (1 to 4) using .CHN

Press to finish; or rMODE epeat steps for all

other channels if desired.

NOTE: In the normal clock display, when either the upper or lower

temperature alarm has been set for a particular channel, the or

symbol will show up solid on the LCD screen when that channel is displayed.

Press or key to set the desired value for the lower temperature limit.+-

To disable the particular alarm, press .

The dotted lines ( ) would reappear to indicate

that the alarm has been disabled.

ALARM

---

Setting the Lower Temperature Alarm

When the Temperature Alarm Sounds

The temperature alarm will sound when the actual temperature has

reached (or exceeded) the upper or lower temperature limit.

The temperature alarm has a distinctive tone different to that of

the clock alarm.

or symbol and temperature limit will blink

Press ANY key to stop the temperature alarm. Or without interruption,

the temperature alarm will automatically stop after one minute.

PAGE 1

PAGE 9

PAGE 2 PAGE 3 PAGE 4

PAGE 10 PAGE 11 PAGE 12

I have a UPM thermometer (WS222 receiver and WT 440 transmitter). It is an older model but works just fine. I would like to know how to set up the receiver so that it reads only the outdoor temperature, rather than switching between indoor and outdoor every 6 seconds. Sometimes this seems to happen on its own, but when changing the clock for daylight savings time, it defaults to alternating between the two. There is not description of this in the manual. Thank you. Submitted on 13-11-2022 at 14:28
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of UPM WS222 in the language / languages: English, French as an attachment in your email.

The manual is 0,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

UPM WS222 Manual

Product: