581329
7
Zoom out
Zoom in
Previous page
1/8
Next page
11
12
17
18
- AA SIZE +
- AA SIZE +
System Type
Gas - Standing Pilot
Gas - Electronic Ignition
Gas - Fire Boiler
Gas - Millivolt System
Oil - Fire Boilers
Oil - Fire Furnace
Electric Furnace
Electric Air Conditioner
Baseboard Electric Heater (120/240V)
Heat Pump/Multi-Stage equipment
Compatible with THM302M / THM303M
Yes
Yes
Yes
Yes
Yes
Some models
Some models
No
No
Two AA size batteries (included)
Wire Stripper/Cutter
(If necessary, to strip the wires)
Level
(If necessary, to level the thermostat)
Masking Tape
(To wrap the exposed wires temporarily and labeling
the disconnected wires)
Hand Power Drill with a 3/16 inch bit
( If necessary, to drill holes on the wall )
Cross (Phillips) screwdriver
Yes
Pre-Comfort Recovery
This thermostat is equipped with a ‘Pre-Comfort Recovery’ system that will activate the heating or cooling in
advance of the actual set program time so that the room will be at the desired temperature at the start of the
comfort program time.
It is normal for the system to be activated earlier (up to ½ hour for heating and one hour for cooling) than the
actual set program time.
The Pre-comfort Recovery can be disabled if desired. Please refer to "Optional Settings".
Usage Monitor
The thermostat tracks the system "ON" time; the time the heating/cooling equipment is running.
Press USAGE once to view USAGE TODAY;
Press USAGE again to view USAGE THIS WEEK.
USAGE TODAY automatically resets itself daily at real-time 00:00
USAGE THIS WEEK automatically resets itself at the end of the week at real-time 00:00
A new week begins Monday morning.
Filter Change
The FILTER CHANGE indicator will display on the LCD screen when the system "ON" time (HEAT or COOL)
has accumulated to approximately 500 hours. It is an indication that the filter should be changed at this time.
To reset the FILTER CHANGE counter press and hold USAGE for 3 seconds until the appears momentarily.
This brings the counter back to zero.
Optional Settings
Below is the list of optional settings:
- 12/24 Hour display format.
- Heat Cycle Rate (select the cycle rate to match the heating equipment).
- Pre-comfort Recovery ON or OFF.
- Backlighting ON or OFF.
To begin, press and hold SET CLOCK for 3 seconds.
SET OPTION symbol will appear and either 12Hr or 24Hr will flash.
- Select your preference of 12Hr or 24Hr by pressing UP or DOWN.
Press SET CLOCK to move on to Cycle Rate.
- Choose from Cr0 to Cr4 by pressing UP or DOWN. See Chart 1
- Factory default is Cr3.
Press SET CLOCK to move on to Pre-comfort Recovery ON/OFF
and Backlight ON/OFF settings.
- Choose from OP0 to OP3 by pressing UP or DOWN. See Chart 2
- Factory default is OP3
The backlight only comes ON in the dark.
If the Backlight is ON (enabled), any key press will turn the backlight
ON for 8 seconds in the "dark".
Compatibility
Generally, equipment with low voltage control is compatible with the THM302M / THM303M thermostat.
For details on compatibility of your particular equipment, please call our technical assistance line.
* Not compatible with any 120/240 volt circuit.
Installation
The following tools may be required for installation:
See below to select a suitable place for the new thermostat installation. And refer to "Replacing Old
Thermostat" section to replace old thermostat.
Cr
Cr0
Cr1
Cr2
Cr3
Cr4
System Cycles per Hour
-
Hydronic heat, condensing gas furnaces
Commercial Unit
Gas or oil forced air (default)
Electric Heat
disabled
2
3
5
7
OP
OP0
OP1
OP2
OP3
Options
Both Pre-comfort Recovery and Backlight are OFF
Only Pre-comfort Recovery - ON; Backlight - OFF
Pre-comfort Recovery - OFF; Only Backlight - ON
Both Pre-comfort Recovery and Backlight are ON
Chart 2
Chart 1
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for UPM THM303M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of UPM THM303M in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of UPM THM303M

UPM THM303M User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info