167857
5
Zoom out
Zoom in
Previous page
1/7
Next page
7
POWERPOWER
PROTECTPROTECT
LPFLPF
40-24040-240
BASS-BOOSTBASS-BOOST
ON OFFON OFF
2.2 Operation- Built-in Crossovers
CROSSOVER FILTER SELECTION
The
TATA
series amplifiers have built-in low-pass and
high-pass crossover filters for bi-amplifying your
system. Select " LPF, FULL or HPF" by moving
the position of the slide switch for each pair of
channels. "LPF" selects the low pass filter. "HPF"
selects the high pass filter. Selecting "FULL" defeats the crossover
functions
FREQUENCY ADJUSTMENT
After selecting the crossover function
,
adjust the low pass or
high pass frequency control with a small screwdriver through
the opening marked “LP/FREQ.” or "HP/FREQ.". Turn
CW to set to a higher frequency, CCW to set to a lower
frequency.
Turning the “BASS BOOST” switch to “ON” increases the level
of frequencies around 45Hz by 12dB.
2.3 Operation- Protection Circuits and
L.E.D. Indicators
“POWER.” L.E.D. INDICATOR- Provides a visual indication
that the amplifier is turned on.
“PROTECT” L.E.D. INDICATOR- Provides a visual
indication that a problem exists and the protection circuitry has
protected the amplifier by shutting it down. Turn the system
off and correct the problem before turning the system on.
THERMAL PROTECTION- The amplifier will shut down if its
temperature exceeds a safe operating level. The amplifier will remain off
until it cools to a safe operating temperature. Exercise care, the exterior of
the amplifier may get uncomfortably hot to the touch before shutting
down.
X-OVERX-OVER
LPF- FULL- HPFLPF- FULL- HPF
8
FUSEFUSE
15A15A
15A
OVERLOAD AND SHORT CIRCUIT PROTECTION- The amplifier
will shut down if a short circuit condition exists, or if electrical current
demands exceed safe levels.
FUSE PROTECTION- A blown fuse indicates a problem that
should be corrected before the fuse is replaced. Always replace
with the same value fuse. Never substitute a larger value fuse.
2.4 Operation- Location of Terminals,
Controls and LED indicators
TA4600, TA4320TA4600, TA4320
1. RCA input jacks 2. High level input 3. Input level adjust
4. Crossover select 5. Low pass freq. 6. High pass freq.
7. Bass boost 8. Mode 9. Power L.E.D.
10. Protection L.E.D.
1. Power terminals 2. Fuse(s) 3. Speaker terminals
A/B CHANNELS
INPUT LEVEL HPF LPF
MIN MAX 40 240 40 240
A
B
X-OVER BASS-BOOST
MODE
LPF
FULL
HPF
POWER
ON OFF
HIGH LEVEL
2CH 4CH3CH
BASS-BOOST
ON OFF
40 240
LPF HPF
40 240
X-OVER
LPF
FULL
HPF
LEVEL
MIN MAX
INPUT
PROTECT
C
D
C/D CHANNEL
4 7 8
1 23 569 105 6 3 1
7 4
FUSE
30A 30A
POWER SPEAKER SPEAKER
BRIDGED
BRIDGED
+12V RMT GND
( A+ ) ( A- ) ( B- ) ( B+ )
( + )
( - )
( C+ ) ( C- ) ( D- ) ( D+ )
( + )
( - )
1 3 32
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate ta 2160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate ta 2160 in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info