Manual Ultimate speed ULG 12 A1 - IAN 100683 (page 40 of 44) (French, Italian)

606437

Zoom out

Zoom in

1/44

40 GB

Operation / Maintenance and care / Warranty and service information

Operation

the best “life“ when recharged before being

drained more than 50 %. When fully discharged

they withstand about 300 charging cycles. The

GEL battery type is similar to AGM. The charg-

ing voltage is lower than for other lead-acid

batteries. Using the wrong charger for a Gel

battery will result in a reduction in power or a

shorter life.

– 6 V Regular: Select this mode for conventional

6 V batteries.

Charge Start button

: Use this button to switch

between the following options

– Fast Charge: charges quickly (recommended in

low outdoor temperatures / winter)

– Normal Charge: normal charging process (nor-

mal speed)

–

Start: brieﬂy delivers 75 ampere to bridge a w

eak

or drained battery to jump start an engine

Attention: This mode can only be exited by unp

lug-

ging the mains plug

Jump starting

Always make all the connections

as described and in the correct order. The vehicle‘s

electronics may otherwise be damaged.

Proceed against the speciﬁcations at your own risk

and responsibility.

Attention: This function is not suitable for batteries

below 45 Ah. This function could damage batteries

below 45 Ah.

Diesel vehicles and large-volume engines in part re-

quire amperages above 75 A for jump starting.

Note: The charger features an analysis program

to protect the battery from damage (e.g. sulphation

or rapid voltage drops), particularly during jump

starting. The device will not switch on the jump start-

er with severely drained or heavily stressed batteries

to protect the battery. During this process the battery

is already being charged with lower currents (Charg-

ing lights up). The display continues to read “0“. In

this event the jump start function cannot be used. This

will protect the battery from damage. You should

then ﬁrst charge the battery. You may also use the

“Fast Charge“ or “Normal Charge“ function for

this purpose.

Connect the car charger‘s mains cable

power.

Connect the red connector clamp

to the

positive battery terminal. (The positive terminal

is marked with a “+“ symbol and a red mark.)

Connect the black connector clamp

to the

negative battery terminal. (The negative terminal

is marked with a “-“ symbol and a black mark.)

If the connector clamps are connected correctly,

the car charger will automatically select the cor-

rect battery type. You may review it in the “Bat-

tery Type“ option ﬁeld and if necessary change

it by pressing the battery type button

Now select the “Start“ function using the Charge

Start button

. The cart charger will now ana-

lyse the battery‘s charge level. The display will

now read “0“.

Start the vehicle‘s ignition. The display will now

show a 5 second countdown (of which 2 second

priming / analysis function and 3 second jump

start function at 75 A) when needing the car

charger for jump starting (previously analysed

by the car charger). During this countdown the

car charger will brieﬂy deliver 75 A to bridge

the battery to start the car. This is followed by

a 180 second pause to protect the battery. The

cycle will now restart (2 second priming / anal-

ysis function and 3 second jump starting at

75 A / 180 second pause).

To disconnect the device, ﬁrst remove the termi-

nal clamps (

) and unplug the power

cord

Note: If the battery is completely drained, the 75 A

will not be suﬃcient to start all engines (e.g. diesel

vehicles).

In this case, please select the “Fast Charge“

option using the Charge Start button

and

charge the battery 60 % (preheating of diesel

engines draws power from the battery. This re-

quires 60 % after preheating).

You can monitor the charging process in the display

by selecting the “Battery %“ option using the digital

display button

Once 60 % has been reached, jump start again.

100683_uls_Kfz-Ladegeraet mit Starthilfefunktion ULG 12 A1_content_CH.indd 40 19.09.14 15:13

I need a part for a parkside gasless welder IAN 291492 can you please Help phone No 07980041407 . email
john.hutchings73@ntlworld.com
Thanks
John Hutchings Submitted on 5-7-2021 at 17:15
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate speed ULG 12 A1 - IAN 100683 in the language / languages: French, Italian as an attachment in your email.

The manual is 2,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ultimate speed ULG 12 A1 - IAN 100683

Ultimate speed ULG 12 A1 - IAN 100683 User Manual - English, German, Dutch, Swedish - 45 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ultimate speed ULG 12 A1 - IAN 100683 Manual

Product: