774517
5
Zoom out
Zoom in
Previous page
1/77
Next page
8 9
EN ZSDR-850 ZIGBEE SMOKE DETECTOR ZSDR-850 ZIGBEE SMOKE DETECTOR EN
1. REMOVE BATTERY PULL STRIP
A Remove the detector from the mounting bracket by twisting it.
B Remove the battery pull strip by pulling it from the detector.
Only after removing the pull strip the detector can be used.
2. INDICATORS
The detector contains a LED indicator to show the status of the
detector. Please see below the meaning of the dierent LED
indications.
LED FUNCTION TABLE
Connection mode LED will flash fast for approximately 1 min.
Connected successfully LED will light up for 3 sec (The App will also
indicate when the connection is successful)
Detector reset LED will flash 6x
Detector alarm LED will flash and detector will sound (85db). To
stop the detector alarm press the Test/Stop button
Detector operation LED will flash once every 53 sec to indicate the
detector is operating correctly
Battery low indication LED will flash once and gives one beep every
53 sec
3. DOWNLOAD APP
To connect the detector with a
Z1 Zigbee bridge or ICS-2000,
first get the App by scanning
the QR code or go to trust.com/
Zigbee and install it.
4. CONNECT DETECTOR
A In the App, select a room,
press the + button and
choose Trust Zigbee line/
Smoke detector and follow the
instructions. For manual set up
of push-notifications go to the
rules tab, press the + button
and select notification wizard.
5. MOUNT THE DETECTOR
A Mount the bracket of the
detector on a flat surface on
the ceiling and secure it with
the included screws.
B 1 Place the detector on the
mounting bracket.
2 Secure the detector by
twisting it on the bracket
to lock it.
6. TEST MODE
Activate the test mode of the
detector to check the operation
by pressing the Test/Stop
button. The LED will flash fast
and the detector will sound.
RESET DETECTOR AND
ACTIVATE CONNECT MODE
Warning: This step will
disconnect the detector from
the Z1 Zigbee Bridge or the
ICS-2000. To reset the detector
press the button in the hole
at the side for approximately 5
sec with the included pin. The
LED will flash 6x to confirm
the reset.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trust ZSDR-850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trust ZSDR-850 in the language / languages: All languages as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info