753343
10
Zoom out
Zoom in
Previous page
1/13
Next page
10 EN
glue gun PGGS 10-230V
Gluing
Warning of hot surface
The nozzle might still be hot after use. Glue coming out
of the nozzle can be hot. Risk of burns.
Do not touch the nozzle bare-handed!
Wear protective gloves!
Info
When further glue sticks are pushed in, the device
requires a little more time for heating up than during
initial use. Hardened glue residues can block the feed
channel.
Info
The surfaces to be glued must be clean, dry and free of
grease.
1. Allow the glue gun to heat up. Push a glue stick suitable
for the material into the feed channel(1) from the rear. Pull
the feed trigger(2) to control the flow of glue for the
intended task.
2
1
2. Apply the glue in dots or lines.
3. Immediately press the two workpieces to be bonded
together for approx.30seconds.
ðAfter approx.5minutes the glue joint will be able to
withstand loads.
4. During work breaks, insert the device into the device
holder or put it down on the wire stand.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
If required, allow the device to cool down.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Slight smoke or odour are emitted during first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages.
Check the on-site fusing.
Info
Wait for at least 10 minutes before switching the
device back on.
The glue stick is not transported:
The glue stick may be used up or too short. Insert a new
glue stick. Only use suitable accessories/ glue sticks as
specified in the technical data.
The glue stick diameter may be too large or too small. Only
use suitable accessories/ glue sticks as specified in the
technical data.
The glue stick falls out of the device:
The glue stick diameter is too small. Only use suitable
accessories/ glue sticks as specified in the technical data.
Liquid glue comes out of the feed channel:
The glue stick diameter is too small and/ or the melting
point of the glue stick is too low. Only use suitable
accessories/ glue sticks as specified in the technical data.
The glue does not come out evenly:
The device may not have reached the melting point yet.
Allow the device to heat up completely.
Pull the feed trigger slowly and evenly.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PGGS 10-230V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PGGS 10-230V in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PGGS 10-230V

Trotec PGGS 10-230V User Manual - German - 13 pages

Trotec PGGS 10-230V User Manual - Dutch - 13 pages

Trotec PGGS 10-230V User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info