753341
12
Zoom out
Zoom in
Previous page
1/14
Next page
12 EN
cordless glue gun PGGS 10-20V
The device does not start:
The battery power might be too low. Recharge the battery.
Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
Check the battery terminals for dirt. Remove any dirt.
Info
Wait for at least 10 minutes before switching the
device back on.
The glue stick is not transported:
The glue stick may be used up or too short. Insert a new
glue stick. Only use suitable accessories/ glue sticks as
specified in the technical data.
The glue stick diameter may be too large or too small. Only
use suitable accessories/ glue sticks as specified in the
technical data.
The glue stick falls out of the device:
The glue stick diameter is too small. Only use suitable
accessories/ glue sticks as specified in the technical data.
Liquid glue comes out of the feed channel:
The glue stick diameter is too small and/ or the melting
point of the glue stick is too low. Only use suitable
accessories/ glue sticks as specified in the technical data.
The glue does not come out evenly:
The device may not have reached the melting point yet.
Allow the device to heat up completely.
Pull the feed trigger slowly and evenly.
The glue only bonds on one side:
The glue may have cooled down before you have pressed
the workpieces together. Press the workpieces to be
bonded together immediately. Heat up quickly cooling
materials with a heat gun. Apply the glue in dots if
necessary.
The glue comes undone after cooling:
The surfaces may be greasy, smooth or dusty. You should
degrease, roughen or clean the surfaces.
The material may not be suitable for bonding with hot-melt
glue. Use special glue sticks.
Glued tiles in humid environments come loose:
Moisture penetrates into the glue joints. Use special
cement-based glue sticks.
Glued shoe soles come undone:
Moisture causes the leather to swell. Use special glue
sticks.
Glue residues (strands) form:
The feed trigger is held after gluing is completed. Let go of
the feed trigger in time.
Wipe off the nozzle when lifting it off the workpiece.
The workpiece melts:
The workpiece consists of heat-sensitive material, e.g.
styrofoam, and is not suitable for bonding with hot-melt
glue. Use special glue sticks.
You suffer burns on your fingers during gluing:
The glue may penetrate through paper or textiles. Wear
protective gloves when working with the glue gun. If
necessary, use a heat-resistant pad, e.g. made of silicone.
The workpiece consists of metal and may have heated up.
Wear protective gloves when working with the glue gun.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PGGS 10-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PGGS 10-20V in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PGGS 10-20V

Trotec PGGS 10-20V User Manual - German - 16 pages

Trotec PGGS 10-20V User Manual - Dutch - 15 pages

Trotec PGGS 10-20V User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info