756405
6
Zoom out
Zoom in
Previous page
1/8
Next page
6 EN
dew point scanner BP25
Carrying out a measurement
Info
Please note that moving from a cold area to a warm
area can lead to condensation forming on the device's
circuit board. This physical and unavoidable effect can
falsify the measurement. In this case, the display
shows either no measured values or they are incorrect.
Wait a few minutes until the device has become
adjusted to the changed conditions before carrying out
a measurement.
Ensure that the surface to be measured is free of dust, dirt
or similar substances.
To be able to gain exact measurement results on surfaces
which reflect heavily, stick matt masking tape to the
surface or apply matt black paint with a very high and
known degree of emission.
Note the 20:1 ratio of the distance to the measuring spot
size. The larger the distance to the object, the larger the
measuring spot diameter and hence, the less precise the
measured result.
1. Point the device at the object to be measured.
2. Press the measurement button(3).
ðThe device switches on.
ðThe temperature of the measured object is shown on
the measurement value display for temperature at the
measuring spot(16). Depending on the settings, either
the ambient temperature, the relative humidity or the
dew point temperature are additionally displayed in the
measurement value display(18).
You can determine the risk of condensation forming at the
measuring spot by reading the scale(15) on the display(8), or
based on the colour of the display illumination. Depending on
the risk of condensation forming at the measuring spot, the
display is illuminated in one of the following colours:
Display colour Meaning
green Surface temperature in normal range
orange Surface temperature near dew point
(borderline). When the alarm is enabled, a
repetitive alarm tone is emitted.
red Temperature of measured surface at or
below dew point.
ATTENTION: Risk of condensation forming!
When the alarm is enabled, a constant
alarm tone is emitted.
Switching the laser pointer on/off
Using the laser button(7) you can switch the laser pointer on or
off.
1. Press the laser button(7).
ðThe laser symbol is displayed in the Laser
indication(11).
ðThe laser(1) is switched on.
2. Press the laser buttonagain to switch the laser off.
ðThe laser(1) is switched off.
ðThe laser symbol is no longer displayed in the Laser
indication(11).
Info
The device memorizes the selected setting when
switching off.
Changing the display °C/°F
1. Press the °C/°F button(5) to change between the units
for the measured values.
ðThe selected unit is shown in the temperature unit
indication(14) of the display(8).
Enabling/ disabling the alarm
Press and hold the °C/°F button(5) for approx. three seconds
to switch the alarm tone on or off.
1. Press and hold the °C/°F button(5) for approx.
threeseconds.
ðAn acoustic signal is emitted.
ðThe symbol appears in the alarm tone
indication(19).
ðThe alarm tone is switched on.
2. Press and hold the °C/°F button(5) for approx.
threeseconds once again.
ðThe symbol appears in the alarm tone
indication(19).
ðThe alarm tone is switched off.
Switching the device off
1. Press and hold the measurement button(3) for approx.
three seconds in SCAN mode.
ðThe device switches off.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec BP25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec BP25 in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec BP25

Trotec BP25 User Manual - German - 8 pages

Trotec BP25 User Manual - Dutch - 8 pages

Trotec BP25 User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info