368335

Topcom twintalker 1400 micro sp Manual

4
Zoom out
Zoom in
Previous page
1/100
Next page
4 TOPCOM TWINTALKER 1400
TOPCOM TWINTALKER 1400
• Replacing or modifying the antenna may affect the PMR radio specifications and violate the CE regulations.
Unauthorised antennas could also damage the radio.
3.6 NOTES
• Do not touch the antenna while transmitting, it could affect the range.
• Remove the battery if the device is not going to be used for a long period.
4 CLEANING AND MAINTENANCE
•To clean the unit, wipe with a soft cloth dampened with water. Don’t use a cleaner or solvents on the unit; they can
damage the case and leak inside, causing permanent damage.
• Battery contacts may be wiped with a dry lint-free cloth.
•If the unit gets wet, turn it off and remove the batteries immediately. Dry the battery compartment with a soft cloth
to minimize potential water damage. Leave the cover off the battery compartment overnight or until completely
dry. Do not use the unit until completely dry.
5 DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment friendly manner.
Do not dispose of batteries in a normal household garbage.
6 USING A PMR DEVICE
To communicate between PMR devices they need to be set all on the same channel and within receiving range (up to
max. 3 km in open field). Since these devices use free frequency bands (channels), all devices in operation share these
channels(total 8 channels). Therefore, privacy is not garanteed. Anybody with a PMR set to your channel can overhear
the conversation.
If you want to communicate (transmitting a voice signal) you need to press the - button (Push to talk). Once this
button pressed, the device will go into transmit mode and you can speak into the microphone. All other PMR devices
in range , on the same channel and in standby mode (not transmitting) will hear your message. You need to wait until
the other party stops transmitting before you can reply to the message. At the end of each transmission the unit will
send a beep. To reply, just press the - button and speak into the microphone.
7 GETTING STARTED
7.1 REMOVING/INSTALLING THE BELT CLIP
1. To remove the clip from the unit, push the belt clip (b) towards the antenna,
while pulling the clip tab (a).
2. When re-installing the belt clip, a click indicates the BeltClip is locked into
position.
7.2 BATTERY INSTALLATION
1. Remove the belt clip (§ 7.1).
2. Press the battery cover and slide it away from the antenna. (c)
3. Install three ‘AAA’ alkaline or rechargeable batteries following the polarity as
shown.
4. Re-install the Battery Cover (c) and Belt Clip (§ 7.1).
PTT
PTT
If 2 or more users press the - button at the same time the reciever will receive
only the stongest signal and the other signal (s) will be supressed. Therefore you
should only transmit a signal (press - button) when the channel is free .
PTT
PTT
a
b
c
+
-
1 x AAA
+
-
1 x AAA
+
-
1 x AAA
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom twintalker 1400 micro sp at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom twintalker 1400 micro sp in the language / languages: English, German, Dutch, Danish, French, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info