484006
5
Zoom out
Zoom in
Previous page
1/85
Next page
5
Babyviewer KS-4245
ENGLISH
®
9 Installing the Babyviewer KS-4245
9.1 Fine tuning
Place the camera in a convenient location, point the lens of
the camera to the observation area.
Adjust the angle by rotation the camera.
10 Operation and use
10.1 Switching the baby unit and parent unit on
and off
Press the on/off switch to switch on the parent
unit. The display is activated.
Slide the on/off switch up to switch on the baby
unit. The on/off LED is activated.
Press the on/off switch to switch off the parent
unit (press and hold until the display goes blank).
Slide the on/off switch down to switch off the
baby unit.
10.2 Checking the connection between the parent
unit and the baby unit
You should always check the wireless connection when you use
the babyphone for the first time.
Put the parent unit in the same room as the baby unit,
separated by at least two metres.
Switch on both devices. The parent unit will try to
establish a connection with the baby unit.
The display of the parent unit will show the captured
image from the baby unit after the connection has been
established (monitor mode).
The sounds picked up by the microphone are
reproduced by the parent unit.
The volume of the reproduced sound is indicated by the
volume LED’s at the top of the parent unit.
The higher the volume, the more LED’s are on.
If no connection is established, the out of range icon is
displayed and a beep is audible.
10.3 Out of range indication
The maximum range between the parent- and baby unit is 300
meter in open area. Different factors, such as bricks and plaster
walls, will reduce the range. Moreover, reinforced concrete floors
will influence the range tremendously.
In a residence, normal operating range is up to 50 meters and 2
floors.
If the connection is interrupted, the out of range icon is
displayed and a beep is audible.
Reduce the distance between the parent and baby units
until a new connection is established.
10.4 Setting the reproduction volume of the
parent unit
There are 5 volume levels.
Press button to increase the volume.
Press button to decrease the volume.
10.5 Setting the parent unit display brightness
When the display in on.
Press the menu button once. The Brightness
icon is displayed.
Press the up or down button to select the
desired brightness (5 steps).
Press the menu button to confirm.
After 10 seconds the parent unit will switch back to
monitor mode.
10.6 Temperature indication
When the display is on, the baby’s room temperature is displayed
in the right lower corner.
To set the temperature unit:
Press the menu button twice. The temperature
icon is displayed.
Press the up or down button to °C
(Celsius), °F (Fahrenheit) or “OFF”, to switch the
temperature indication off.
Press the menu button to confirm.
After 10 seconds the parent unit will switch back to
monitor mode.
10.7 Talking with your baby
You can use the parent unit to talk with your baby.
Press the Talk button on the parent unit and hold
it pressed.
Hold the parent unit vertical with the microphone
approximately 10 cm from your mouth, and speak into
the microphone.
Release button when you have finished talking.
10.8 Playing a lullaby
There are 5 pre-programmed lullabies that you can play on the
baby unit.
To play the currently selected lullaby or stop playback,
press the play button on the baby unit.
To select a different lullaby, repeatedly press the lullaby
button until the desired lullaby is selected. The
lullaby icon will display the selected lullaby (1 to 5). If no
number is displayed, next to the lullaby icon, all songs
will be played successively.
When the lullaby starts playing, you have 10 seconds to set the
volume of the lullaby.
Press the up button to increase the volume or
the down button to decrease the volume.
10.9 Switching the night light on and off
Press the menu button 3 times. The night light
icon is displayed.
Press the up or down button to switch
the night light “ON” (night light is on) or “OFF”.
Press the menu button to confirm.
After 10 seconds the parent unit will switch back to
monitor mode.
10.10 Voice activated transmission (VOX)
During night and to save energy, the Babyviewer KS-4245 can be
set in VOX mode.
In VOX mode, the display will be activated as soon as the
microphone of the baby unit will capture sound.
You can set the sound detection sensitivity (VOX) of the
babyphone. If the sensitivity is set to high, the baby unit will pick
up weaker sounds.
Press button 4 times. “VOX” is displayed.
Repeatedly press button or to set the
VOX sensitivity.
CAUTION
Do not place the camera and wires within the baby’s reach!
Fix the camera at least 1 meter away from the baby.
The parent unit will try to establish a connection
with the baby unit. If captured image from the
camera is displayed, a connection has been
established.
29
20
4
29
4
6
14
16
17
16
Allow your baby to get used to the talk function
before you use it in practice.
10 seconds after starting or selecting the
lullaby, the parent unit will return to monitor
mode. The up button and down
button can than only be used to set
the volume of the parent unit.
To set the volume of the lullaby in monitor
mode, switch the lullaby off and on using
the button first before selecting the
volume.
23
16 17
23
PTT
PTT
24
PTTPTT
24
18
16
17
16
17
18
23
16
17
2
23
23
16
17
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Babyviewer 4500 - KS 4245 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Babyviewer 4500 - KS 4245 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 69,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info