Manual Thomson ROC4407 4in1 (page 1 of 3) (English)

607834

Zoom out

Zoom in

1/3

This universal remote control (4 in 1) is compatible with the majority of television sets, DVD

players and video recorders, as well as digital boxes such as satellite or cable receivers,

DVBT receivers (Digital Video Broadcast Terrestrial), ADSL decoders, and so on. Together these

digital boxes are called STB (Set Top Boxes).

This remote control was programmed in the factory, so that you can use it to control most of

the sets of the THOMSON group’s make. For this reason, we recommend that prior to

attempting to programme the remote control, you try it out by means of one of the methods

described in this user manual. However, first of all, you must install 2 batteries (AAA) in the

remote control.

Please keep this guide along with the code list (provided separately), so that you can

subsequently programme your remote control for use with other sets.

1 On/Standby or Standby only, depending on the

equipment being used.

2 Mode keys. Select the device to control (TV,

DVD, …).

3 Selection of channels, input of digital values,

channels with 2 digits, external TV/VIDEO sources

(AV connectors).

4 Programming of the remote control.

5 Zapping and commands or the muting of sound.

6 Activation and use of menus (display, deletion,

choice, confirmation).

7 Activation and use of teletext (Videotext).

9 Operating a video cassette recorder (VCR) or a

DVD player (DVD).

Use of teletext (Fastext) or functions specific to

certain devices.

Note:

depending on the actual devices, manufacturers

and year of manufacture, the functions available will

vary.

DVBT (Digital V

ideo Broadcast Terrestrial):

for the

countries that have this service, you can control a

DVBT receiver by programming a code on the list

under the

STB

mode key.

The keys

Testing the remote control

before programming

Programming

the remote control

1. Switch on the set you want to control.

2. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player,

VCR: video recorder,

STB: satellite receiver, cable, DVBT, ADSL.

3. Direct the remote control towards the TV set and try

to switch it off by simply pressing the key

. If the

device does not turn off, you must program the

remote control using one of the methods A, B, C or

D described hereafter.

Note 1:

Except for the

key, each key of the (

DVD

VCR

, ...) mode can be programmed to control a

device other than that indicated on the key. It is

therefore possible, for example, to allocate allocate

STB mode to the

DVD

key. Yo u must enter the code

corresponding to the manufacturer and the device by

using one of the methods indicated in this manual.

However, method D (automatic search for a code)

will greatly simplify the task for you. In this case it is

only necessary to enter a code from the list that

corresponds to the type of device, for example: 0603

for a Thomson satellite receiver) and then to run the

automatic search procedure. The remote control will

then test all the codes automatically until it finds those

that control the receiver.

Note 2:

To control 2 devices of the same type and the

same brand (2 Thomson VCRs, 2 Thomson satellite

receivers, ...) ensure first that these two devices are

not set to react to the same sub code, they will require

one sub code for one and a different sub code for the

other (i.e., codes A and B with Thomson devices).

Once you have checked this, successively program 2

separate mode keys using method D.

Method A – Fast programming

with 1-digit subcode

Method B – 4-digit codes

programming

Before you start programming, you must find the

subcode of the set to be controlled. Entering a sub-

code lets the remote control test a predefined list of

codes. Refer to the list provided with these instructions,

page I of the subcodes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks and

then remains lit (the indicator light remains on for a

few seconds to give you the time to proceed with the

following steps. The indicator lamp flashes to signal

that this time is almost up, and then goes off).

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player,

VCR: video recorder,

STB: satellite receiver, cable, DVBT, ADSL.

4. While the indicator is lit

, type in the subcode

(example: 1 for THOMSON).

5. Direct the remote control towards the set and

switch it off by pressing the key

6. If the set you want to control switches off, press OK

to memorise the code.

7. Should the set not switch off, press key

repeatedly, until the set switches off. Between two

key presses, leave enough time for the key

corresponding to the selected mode enough time to

light up again (about 1 second). Proceeding this

way will enable you to see whether the set responds

or not.

8. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Before you start programming, you must find the code

of the set to be controlled.

Refer to the list provided with these instructions, page II

of the codes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit (the indicator light remains on

for a few seconds to give you the time to proceed

with the following steps. The indicator lamp flashes

to signal that this time is almost up, and then goes

off).

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player,

VCR: video recorder,

STB: satellite receiver, cable, DVBT, ADSL.

4. While the indicator is lit

, enter the first digit of the

4-digit code proposed for the set to be controlled

(example: 0036 for Thomson).

5. Direct the remote control towards the set and try to

switch it off by pressing the key

F01_GB_ROC4407.qxp 22/01/07 16:49 Page 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC4407 4in1 in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson ROC4407 4in1

Thomson ROC4407 4in1 User Manual - German - 3 pages

Thomson ROC4407 4in1 User Manual - Dutch - 3 pages

Thomson ROC4407 4in1 User Manual - French - 3 pages

Thomson ROC4407 4in1 User Manual - Spanish - 3 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC4407 4in1 Manual

Product: