607826
1
Zoom out
Zoom in
Previous page
1/3
Next page
The ROC 2206 is a universal remote control (2 in 1). It can replace 2 remote controls thanks to its
2 mode keys TV, VCR/DVD... It is compatible with the majority of television sets, video cassette
recorders, DVD players, satellite and cable receivers as well as terrestrial digital television (DVBT),
amplifiers and other audio equipment provided they are controlled by infra red signals.
This remote control has been factory programmed to allow you to use it immediately with the
majority of Thomson Group devices.We therefore advise you to try it before beginning to program it.
If programming is necessary, follow one of the methods A, B, C, D or E that are given in this manual.
But before anything else, fit the two batteries into the remote control handset and peel off the tab as
shown on the diagram on the inside of the cover.
Keep these instructions and the separate list of codes in a safe place so that you can later reprogram
your remote control.
1 I ndicator lamp: the indicator lamp lights up when any
key is pressed.
2 B: On / Standby.
3 R emote control mode
Selects device to control TV, DVD,VCR,...
4 S: programmes the remote control.
SHIFT: activates the secondary key features
(indications in blue).
5 I (EXIT): teletext Off in TV mode.
SHIFT and EXIT: turns off the menu of the
selected product.
6 c: switches the TV sound off.
SHIFT and OK: confirms a selection.
7 VOL-/VOL+ increases (+) or decreases (-) the
volume of the TV set.
SHIFT and VOL-/VOL+ also allows you to
navigate the menus horizontally.
8 M (RECORD): to record (VCR/DVD).
9 F (FF): fast forward *.
10 B (Play): play*.
1 1 K (Pause): stops on an image*.
1 2 Number keys 0 to 9: these keys have the same
functions as those of your original remote and are
also used to enter the codes fo
r
diff
er
ent pr
oducts
.
1 3 AV: for selecting an external source (SCART).
14 Press this key first before you type in the 2-digit
channel number (except for Thomson group
products).
1 5 L (STOP): stop playback*.
1 6 G (REW): goes backward or advances forward*.
17 "Info" key.
Videotext inlay on TV picture.
18 PROG+,PROG-: programmes zapping button
(received by the television set or the satellite
receiver); use to scroll vertically through menus
SHIFT and PROG+/PROG- also allow you to
navigate the menus vertically.
1 9 a (MENU): teletext On/Off in TV mode.
SHIFT and MENU: turns on the menu of the
selected products.
* The coloured buttons can be used to select categories
when teletext is activated, and specific functions
depending on the make.
2 - Te sting the remote control
before programming
1. T urn on the device that you wish to control.
2. P ress the key corresponding (3) to the type of device
to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player.
3. P oint the remote control at the device you wish to
control and try to turn it off using the
B
(2) key.
I f the device does not turn off, you must program the
remote control using one of the methods A, B, C or
D as described below.
1 - Description of keys
3 - Programming
the remote control
Before you start programming, you must find the subcode of
the set to be controlled.
Refer to the list provided with these instructions, page I of the
codes.
1 S witch on the set you want to control.
2. Hold down the S (4) key until the indicator lamp
(1) remains lit (the indicator light remains on for a
few seconds to give you the time to proceed with the
following steps. The indicator lamp flashes when this
time is almost up, and then goes off).
3. P ress the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player.
4. W hile the indicator is lit, type in the subcode (example:
1 for Thomson).
5. D irect the remote control towards the set and try to
switch it off by pressing the
B
(2) key.
6. I f the set you want to control switches off, press
c (6) to memorise the subcode.
7. If the product doesn’t turn off, press the
B
(2)
key repeatedly until the set switches off. Wait
approximately one second between key presses to
give the indicator lamp (1) enough time to go off
and light up again. This will allow you to see whether
the product responds or not.
8. I mmediately upon the switching-off of the set to be
controlled, press c (6) to store the subcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control (with the exception of the
TV button which can only be used to control a television set),
begin by entering the code that corresponds to the product you
want to programme (a 4-digit code that you will find in the code
booklet – see method B).
Example: if you want to control a satellite receiver with the
VCR/DVD key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands. Check your remote control for proper functioning by
performing the test described on page 3.
Method A – Fast programming with
1-digit subcode
GB
1
01_ROC2206_GB.indd 1 30/11/06 16:56:21
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC2206 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC2206 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson ROC2206

Thomson ROC2206 User Manual - German - 3 pages

Thomson ROC2206 User Manual - Dutch - 3 pages

Thomson ROC2206 User Manual - French - 3 pages

Thomson ROC2206 User Manual - Spanish - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info