472029
15
Zoom out
Zoom in
Previous page
1/17
Next page
EN
12
English
• Set
Record
to check if you really want to start
your scheduled recording when the time you
have set comes. When time is out and you do
not execute any operation, scheduled recording
will start automatically.
-
Repeat type
: set different repeat modes for the
recording.
4.
Press
▲/▼/
/► to select
Add
, then press
OK
to
add the schedule you set into your schedule list.
5.
Press the red button to repeat above procedures
to add another schedule.
6.
If you wish to edit or delete a schedule, select it
and press
OK
to enter.
7.
Press
EXIT
to close the menu.
Network connection
You can set up your TV so that it can access the
Internet through your local area network (LAN) using
a wired or wireless connection.
Connecting to a wired network
You can attach your TV to your LAN using cable in
three ways:
You can attach your TV to your LAN by connecting
the LAN port on your TV to an external modem
using a Cat 5 cable.
You can attach your TV to your LAN by connecting
the LAN port on your TV to an IP Sharer, which is
connected to an external modem. Use Cat 5 cable
for the connection.
Depending on how your network is congured,
you may be able to attach your TV to your LAN by
connecting the LAN port on your TV directly to a
network wall outlet using a Cat 5 cable. Note that
the wall outlet is attached to a modem or router
elsewhere in your house.
Select
Smart TV > Settings > Interface
, then select
Ethernet
to connect to a wired network.
Connecting to a wireless network
To connect your TV to your network wirelessly, you
need a wireless router or modem and a Wireless
LAN Adapter. Connect your Wireless High-Gain USB
Adapter (USB dongle) delivered with your TV to your
TV’s
USB 1
port.
1.
Select
Smart TV > Settings > Interface
, then
select
Wireless
to connect to a wireless network.
2.
Select
Wireless setting
and press
OK/
► to enter.
3.
Connection Methods
: You can setup the wireless
network connection three ways.
-
Scan
Select
Wireless setting
> Scan
, then press
OK/
►, the TV will scan all access points within
range. The access points found by the TV will
be displayed.
Select an available access point, then press
OK/
► to connect the TV.
Notes:
- If you select a protected access point, you will
have to enter the corresponding password.
Press
MENU
on the remote control to display
the virtual keyboard to enable you to enter the
password.
- This set has a memory function of available
access point, which enables your set to be
connected to the network even if you switch
on the TV after power off.
-
Manual
Select
Wireless setting
> Manual
, then press
OK/
►, you will be prompted to enter the correct
SSID of an available wireless router to set up the
connection.
-
Auto
If your AP supports WPS (Wi-Fi Protected
Setup), you can connect to the network via PIN
(Personal Identication Number) or PBC (Push
Button Conguration). WPS will automatically
congure the SSID and WPA key in either mode.
Select
Wireless setting
> Auto
, then press
OK/
► to enter.
PIN
: Select
PIN
and press
OK/
► to enter.
Generate a random PIN code. Make sure
this code is installed on the AP. (For the
procedures, refer to your router manual.) Press
OK/
► again to set up the connection.
PBC
: If your router has a PBC push button,
select
PBC
, then press
OK/
► to enter. Press
the PBC push button on your router within 2
minutes after you press
OK/
► again. Your TV
will automatically acquire all the network setting
values it needs and connect to your network.
Network setup
1.
Press
MENU
on the remote control and select
Smart TV > Settings > Internet connection
.
Press ◄/► to select
On
. Wait until the connection
is automatically established.
2.
Select
Smart TV > Settings > Connection
test
, then press
OK/
to check the Internet
connectivity. If it does not work, follow below steps
to make sure of the connectivity.
3.
Select
Smart TV > Settings > IP setting
, then
press
OK/
to enter the
IP setting
menu.
- Set
Address type
to
Auto
, it will acquire and
enter the needed IP address automatically.
- You can follow below steps to enter your IP
address manually.
Set
Address type
to
Manual
, then press ▼ to
go to the rst entry eld.
Enter the
IP address
,
Subnet mask
,
Default
gateway
,
Primary DNS
and
Secondary DNS
values. Use the alphanumeric buttons to enter
Network connection
Chapter 5
15


Need help? Post your question in this forum.

Forumrules
1

Forum

thomson-46ft8865

Reset search

  • Thomson tv 46ft8865 connect wired headphones to the first out of three on the tv. Headphone sound ok, but cannot switch to speaker from remote unless removing jack from tv.
    Any solutions, please.
    Thank you Submitted on 5-7-2017 at 14:59

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson 46FT8865 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson 46FT8865 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson 46FT8865

Thomson 46FT8865 User Manual - German - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info