771163
49
Zoom out
Zoom in
Previous page
1/52
Next page
43
EN
Trouble Shooting
Problems
Check
The screen of the
control panel does not
turn on.
Make sure the switch on the back or on the side of the device is in
position I.
Make sure the device is connected to the electrical system.
The device is not
heating.
If the device is in programming mode, make sure the programming
in set at COMFORT.
Make sure the circuit breakers of the system are activated or that the load
shedder (
if you have one
) did not out powered the heater.
If the temperature of the room is higher than the set temperature, it is
normal the device is not heating.
The device is heating
all the time.
Make sure the device is not located near an air stream or
the set temperature was not increased.
The device is not
heating enough.
Increase the Comfort set temperature.
If it is set at the maximum temerature, check the following:
- Check if another heating mode exists in the room.
- Make sure your device is only heating the room (closed door).
- Have the power supply to the device checked.
- Check if the power of your device is adapted to the size of your room
(
we recommend an average of 100 W/m2 for a ceiling height of 2,50m or
40W/m3
).
The surface of the
device is very hot.
It is normal for the device to be hot when in use. The maximum surface
temperature is limited according to the NF Electricity Performance
Standard. However, if you feel that your device is still too hot, make sure
the power is adapted to the size of your room (
we recommend 100W/m²
for a ceiling height of 2,50m or 40W/m3
) and that the device is not placed
near an air stream which would affect its control mechanism.
Dirty marks appear on
the wall around the
device.
The dirty marks come from the bad quality of the air in the room. In this
case, you are advised to check that the room is correctly aired (
ventilation,
vent duct, etc.
), that the air is clean and not to smoke in the room. Your
device will not be replaced under guarantee because of these dirty marks.
The Expert Menu is
not accessible.
You saved a PIN. You must enter your PIN to access the Expert Menu
(see Expert menu section).
The device does
not follow internal
programming
commands.
Check the set date and time.
Make sure the device is in PROG MODE and internal programming is
selected.
The device does
not follow external
programming
commands.
Make sure the programming unit is used properly (see the operating
instructions of the Control Unit). Make sure the device is in PROG
MODE and the external control is selected.
If you were not able to solve your problem, contact a professional with
your device references found on the nameplate (
commercial code (C
),
commercial code (C
commercial code (C
serial No. (E))
, room temperature and maybe the programming system
references. You may also have to provide information contained in the
Information Part of the Expert Menu.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermor Emotion 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermor Emotion 4 in the language / languages: English, French as an attachment in your email.

The manual is 4.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info