Manual TFA 37.3000 (page 12 of 14) (English, German)

669386

Zoom out

Zoom in

1/14

2322

THERMO-TIMER



• The temperature sensor is waterproof, so you can also

control the temperature of liquids. The sensor cable

has a length of 1 m and is situated, together with the

sensor, in the sensor compartment at the bottom of the

device. In the case of temperature measurements, this

must be removed and placed at the desired location.

7.2 Mode 2

Timer-mode ” “

• The device switches on and off according to the three

user-adjustable time pairs (1 time pair = 1* on /off).

The three time pairs always refer to 1 day (24 h) and

repeat daily if they are not changed.

Enable Timer-mode ” “

• The display shows the time or the current temperature.

a) Press the [set] key once.

b) Press the [mode] key repeatedly until “-: -” appears on

the display as well as a flashing ” “. The [h] and [m]

keys allow you to set the start time of the 1st time-pair.

The number displayed in the lower right corner of the

display (here 1) indicates which time-pair is display-

ed, the "ON" displayed in the upper right corner indi-

cates that it is the switch-on time.

c) Now press the [set] key once. The display shows “-: -”

and the character "INT" (interrupt) appears in the

upper right corner. The switch-off time of the first

time-pair can now be programmed using the [h] and

[m] keys. The device switches according to program-

ming when reaching the respective switching points.

d) By pressing the [set] key and repeating the procedure

described under b) and c), the second and third time-

pairs can now be programmed. To return to the nor-

mal display mode, press the [set] key again. If only

1 time-pair is to be programmed, you can press the

[set] key repeatedly to skip without input of the follo-

wing time-pairs.

THERMO-TIMER



Disable Timer-mode

a) Press the [set] key once.

b) Press the [mode] key repeatedly until the display

shows the start-up time of the first time-pair, as well

as a flashing “ON” and “1”. With the [manual] key,

you can now disable the switch on time of the first

time-pair. The display also shows “X”. The previously

set values are kept. When the [manual] key is pressed

again, the “X” in the display disappears and the

switch-on time of the first time-pair is once more

activated.

c) After the desired setting, press the [set] key. The

switch-off time of the first time-pair, as well as flas-

hing “INT” and “1” are displayed. You can use the

[manual] key to change the settings to deactivate and

activate the switch-off time of the first time-pair, as

described in point b).

d) By pressing the [set] key again and repeating the pro-

cedure described under b) and c), the second and

third time-pairs can now be deactivated and activated.

Press the [set] key again to return to normal display

mode.

By pressing the [manual] key, you can manually switch

the unit on and off at any time.

7.3 Mode 3

Thermo-Timer mode ” “ ” “

• This mode establishes a link between the temperature

(Thermo-mode) and the time (Timer-mode). The

device switches when the programmed temperature is

exceeded or fallen below during the set time. You

have the possibility to program 3 time-pairs with

3 different switching temperatures.

Please note that the Thermo-Timer mode is only acti-

vated when it enters the next set time pair.

TFA_No. 37.3000_Anleit_11_16 21.11.2016 16:30 Uhr Seite 12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of TFA 37.3000 in the language / languages: English, German as an attachment in your email.

The manual is 0,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

TFA 37.3000 Manual

Product: