Manual TFA 35.1099 Primus (page 8 of 31) (English)

506914

Zoom out

Zoom in

1/31

f. Place the solar rain senor under bright environment to charge-up the

rechargeable batteries.

3. Insert two "C" size batteries into the thermo-hygro sensor with the correct polarity.

4. Insert three "C" size batteries into the wireless display with the correct polarity.

NOTE: Every time the wireless display receives data from the sensors, the

wireless icons

will blink once and then return to solid if the last transmission

was successful. A wind speed or rainfall amount that reads "0" does not mean

reception failure, it means that there was no wind or rain at the time of the last

measurement. The thermo-hygro sensor syncs with the wind and rain sensors

and sends all outdoor sensor data to the display. The thermo-hygro sensor tries

for 7 minutes to sync to the wind sensor and for the rain sensor. If not successful

within 7 minutes, the thermo-hygro sensor will stop looking for the other sensors.

5. Setup troubleshooting: If the sensor data fails to display for any of the outdoor

sensors within 10 minutes, (“- - -“ is displayed), remove the batteries from all

units (except for the Wind Sensor) for 1 minute and start the Setup procedure

again at Step 1 and completely reset the solar Rain Sensor (see Step 2:

Important).

ADDITIONAL NOTES FOR THE SOLAR WIND AND RAIN SENSORS MODES:

IDLE MODE

This mode aims to reduce the power consumption of the transmitter. Under this mode,

the sensor stops the transmission of signal, checks the battery voltage and detects the

solar cell condition. The IDLE mode happens if the battery voltage is low.

Note: The sensor will check and charge up the rechargeable battery automatically.

When it detects that the battery voltage is sufficiently charged up and high enough, the

transmission of signal starts again.

STOP MODE

It is the most energy saving mode. Under this mode, the transmitter stops the

transmission of signal. There is no checking of the battery voltage and no detection of

the solar cell condition. The STOP mode happens:

• If the user covers the solar cell for 10 seconds and presses the RESET

button (Wind Sensor).

• If the sensor(s) is(are) placed in the dark environment for 72 hours.

Note:

• To restart the Solar Wind sensor, user should spin the wind cups or place

the sensor in a bright environment, then press the RESET button once to

wake it up again.

• To restart the Solar Rain Sensor, should swing the seesaw or, follow the

SETTING UP, Step 2: Important instructions to completely reset the sensor.

IMPORTANT! During the restart process, if the battery voltage is sufficiently high

enough, the transmission of signal starts again. However, if the battery voltage is low,

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of TFA 35.1099 Primus in the language / languages: English as an attachment in your email.

The manual is 1,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of TFA 35.1099 Primus

TFA 35.1099 Primus User Manual - German - 33 pages

TFA 35.1099 Primus User Manual - French - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

TFA 35.1099 Primus Manual

Product: