Manual TFA 35.1093 - Lumax Funk (page 5 of 18) (English, German, Dutch, French, Italian, Spanish)

466156

Zoom out

Zoom in

1/18

LUMAX – Wireless weather station

╞

Housing

N. Wall mount hole

O. Jack

P. Stand (optional)

Q. Battery compartment

2.2. Transmitter Fig. 2

D1: Transmission indication LED

D2: Wall mount hole

D3: Battery compartment holders

D4: “CH” button

3. Getting started

• Place the display unit and the transmitter on a desk with a distance of approxi-

mately 1.5 meter. Check that no other electronic devices are close.

• Insert the adapter into the jack (O). Connect the power adapter to a wall socket.

Important: Make sure that your household voltage is 230V! Otherwise your

weather station may be damaged.

• When the base station is powered up, a short beep will sound and all LCD

segments will light up for about 2 seconds before it enters into learning mode to

learn the sensors security code.

• Pull down and take away the holder of the weather station and insert 2 x AAA

1,5 V batteries into the battery compartment, observing the correct polarity.

• The batteries will operate as a backup power source in case of power failure.

• Open the battery compartment of the transmitter by pushing inwards the two

latches at the bottom and insert 2 x AA 1,5 V batteries, observing the correct

polarity.

• The LED indicator of the transmitter is blinking and the transmitter is set to

channel 1 by default.

• After the sensor is powered up, it will first transmit the temperature and then the

sensor will start radio controlled time reception. During the DCF time reception

period (maximum 10 minutes), no weather data will be transmitted.

• After the reception of the radio controlled time the DCF signal appears perma-

nently on the display of the weather station.

• Note: DO NOT PRESS ANY KEY during the first 10 minutes learning period or be-

fore radio controlled time is displayed on the receiver. After both outdoor values

and radio controlled time are displayed you can place your remote sensor out-

doors at the final destination. In case the clock cannot detect the DCF-signal (for

example due to disturbances, transmitting distance, etc.), the time can be set

manually. If the outdoor weather data is not displayed or if any key is pressed

before the weather station receives the signal, or when changing the transmitter

batteries you will need to follow the installation procedure again. Please wait

minimum 10 seconds to make a proper reset for both transmitter and receiver.

Note for Radio Controlled Time DCF:

• The time base for the radio controlled time is a Caesium Atomic Clock operated by

the Physikalisch Technische Bundesanstalt Braunschweig which has a time de-

viation of less than one second in one million years. The time is coded and trans-

mitted from Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 kHz)

and has a transmitting range of approximately 1,500 km. Your radio-controlled

clock receives this signal and converts it to show the precise time in summer or

wintertime. The quality of the reception depends greatly on the geographic loca-

tion. In normal cases, there should be no reception problems within a 1,500 km

radius around Frankfurt.

LUMAX – Wireless weather station

╞

1. Introduction

This new wireless thermometer consists on a base station with indoor sensors for room

temperature and atmospheric pressure and a remote sensor for measuring outdoor tem-

perature. So you get useful information about weather and temperature in and around

your house. This is fun and makes you curious to know more.

Please read this instruction manual carefully and keep it!

1.1Content

• Display Station

• Power adapter

• Batteries

• Stand (optional)

• Outdoor transmitter

• Manual

1.2Features

• Outdoor temperature wireless (433 MHz), distance range up to 30 m (free field)

• Indoor temperature

• Maximum and minimum values

• Weather forecast with symbols and tendency of atmospheric pressure

• Radio controlled clock with alarm and snooze function

• Permanent LED backlight

• For wall mounting or table standing

2. Elements

2.1 Receiver (Display unit) Fig. 1

LCD

A. IR motion sensor

B. Weather tendency indicator

C. Weather forecast icon

D. Battery icon for weather station

E. Radio controlled time

F. Alarm icon

G. Radio controlled time icon

H. Indoor temperature display

I. MAX function for indoor temperature

J. Battery icon for outdoor sensor

K. Channel number of outdoor transmitter

L. MAX function for outdoor temperature

M. Outdoor temperature

Buttons

1. “ “ button

2. “MAX/MIN“ button

3. “MENU/SETUP“ button

4. “CH“ button

5. “▲“ button

6. “▼“ button

7. “RESET“ button

Use a pin to press the “RESET” button and restore all settings to factory default.

8. “BRIGHT/DIM“ button

Press the button and you can select a bright LED display or a dim one.

TFA_No_35.1093_Anleitung 09.10.2008 17:54 Uhr Seite 5 (Schwarz/Process Black Auszug)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of TFA 35.1093 - Lumax Funk in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

TFA 35.1093 - Lumax Funk Manual

Product: