Temperature transmitter
1. Functions
• Additional temperature transmitter for wireless
weather stations (e.g. 35.1110)
• For the wireless transmission of outdoor temperature
and DCF time (433 MHz), transmission range up to
50 m (free field)
• Also for temperature control of remote rooms,
f. e. children’s room, wine-cellar
2. Elements Fig. 1
D1: Transmission indication LED
D2: Wall mount hole
D3: Battery compartment holders
D4: Channel-button
D5: °C/°F button
D6: RESET button
3. Getting started
• Place the display unit and the transmitter on a desk
with a distance of approximately 1.5 meter. Check that
no other electronic devices are close.
• Take the display unit into operation according to the
manual of the display unit.
• Open the battery compartment of the transmitter by
pushing inwards the two latches at the bottom and
insert 2 x AA 1.5 V batteries, observing the correct
polarity.
• The LED indicator of the transmitter is blinking and the
transmitter is set to channel 1 by default.
• After the sensor is powered up, it will first transmit the
temperature and then the sensor will start radio con-
trolled time reception. During the reception period
(maximum 10 minutes), no weather data will be trans-
mitted.
Please take note of the following:
• The radio controlled time receiver is built inside the
thermo-sensor. It is recommended to keep distance to
any interfering sources and ferro-concrete buildings.
• During night-time, the atmospheric disturbances are
usually less severe and reception is possible in most
cases. A single daily reception is adequate to keep the
accuracy deviation below 1 second.
4. Positioning of the transmitter
• Choose a shady and dry position for the transmitter.
(Direct sunshine falsifies the measurement and conti-
nuous humidity strains the electronic components
needlessly)
•
Check the transmission of 433 MHz signal from the trans-
mitter to the display unit (transmission range 50 m free
field). Within ferro-concrete rooms (basements, super-
structures), the received signal is naturally weakened.
• If necessary choose another position for transmitter
and/or display unit.
5. Additional transmitters
• For having more than one external transmitter, select a
different channel (2 to 3) for every transmitter by pres-
sing the “CH” button on the transmitter while the
transmission indication LED is flashing. Press once for
channel 2 and twice for channel 3 right after the star-
ting up of the transmitter. The LED is flashing once for
channel 1, twice for channel 2 and three times for
channel 3.
• Press and hold the “B1” button on the display unit for
2 sec. to start initialization manually. The channel num-
ber on the LCD of the display unit flashes and the new
transmitter will be received automatically (model
35.1110).
6. Battery replacement
Caution!
Risk of injury:
•
Keep the batteries out of reach of children.
• Batteries must not be thrown into the fire, short-circui-
ted, taken apart or recharged. Risk of explosion!
• Batteries contain harmful acids. Low batteries should
be changed as soon as possible to prevent damage cau-
sed by a leaking battery. Remove the batteries if you do
not use the product for a lengthy period. Never use a
combination of old and new batteries together nor bat-
teries of different types (e.g. zinc-carbon and alkaline
batteries). Wear chemical-resistant protective gloves
and glasses when handling leaked batteries.
7. Waste disposal
• This product has been manufactured using high-grade
materials and components which can be recycled and
reused.
Never throw flat batteries and rechargeable
batteries in household waste. Never use a
combination of old and new batteries
together nor batteries of different types (e.g.
zinc-carbon and alkaline batteries).
As a consumer, you are legally required to take
them to your retail store or to appropriate
collection sites according to national or local
regulations in order to protect the environ-
ment.
The symbols for the heavy metals contained
are: Cd=cadmium, Hg=mercury, Pb=lead
This instrument is labelled in accordance with
the EU Waste Electrical and Electronic Equip-
ment Directive (WEEE).
Please do not dispose of this product with
other household waste. The user is obligated
to take end-of-life devices to a designated
collection point for the disposal of electrical
and electronic equipment, in order to ensure
environmentally-compatible disposal.
8. Specifications
Transmitter:
Measuring range: -20°...+60 °C /
(transmitter) -4°...+140 °F, °C/°F-switchable
Resolution: 0.1°C / 0.2°F
Transmission frequency: 433 MHz
Transmission time: 60 – 75 seconds
Transmission signal: Once - Channel 1
Twice - Channel 2
Tree times - Channel 3
Transmission range: Max. 50 m
Power consumption: 2 x 1.5V AA
Housing dimension: 75 x 25 x 93 mm
TFA Dostmann GmbH & Co. KG, Zum Ottersberg 12, D-97877 Wertheim
No part of this manual may be reproduced without written consent of
TFA Dostmann. The specifications of this product may change without
prior notice.
DECLARATION OF CONFORMITY
We herewith declare that this wireless transmission device conforms to
the essential requirements of the R&TTE Directive 1999/5/EC.
A copy of the signed and dated Declaration of Conformity is available
on request from info@tfa-dostmann.de.
TFA Dostmann GmbH & Co.KG, D-97877 Wertheim / www.tfa-dost-
mann.de
04/11
Kat. Nr. 30.3186
Bedienungsanleitung
Instruction manual
Fig. 1
Temperature transmitter
Temperature transmitter
D 1
D 7
D 4
D 2
D 3
D 6
D 6
D 5
Front
Back
Bottom
TFA Anl_No. 30.3186 09.05.2011 11:57 Uhr Seite 2
