562463
6
Zoom out
Zoom in
Previous page
1/8
Next page
6
• Ultima 40 Mk 2
Connecting
Connection variations
A connector terminal with four
terminal clips is located on the back
side of the speakers. Here you can
connect the speaker cables directly
or with pin plugs. We only describe
the direct connection in these instruc-
tions.
The terminals are each marked in
red (+) and black (-).
In addition to a standard connection,
where every speaker column is connected to the amplifi er
with a cable, you can also choose the variants “Bi-Wir-
ing” or “Bi-Amping”.
Standard connection
With this connection, the Ultima 40 Mk 2 speakers are
connected like conventional speakers with one double-
strand speaker cable each. The contact bridges between
the connector terminators may not be removed in the
process. You can connect the cables accordingly to the
top or bottom terminals.
Bi-Wiring
With Bi-Wiring, the speaker is connected to the fi nal
amplifi er using two separate speaker cables for the bass
sound and mid/treble sound branch. This decoupling of
the speaker systems may improve the sound quality.
Bi-Amping
In case of Bi-Amping, the bass sound and mid/treble
sound branch are each powered by an own power ampli-
er of the amplifi er. You connect a double-strand speaker
cable to each power amplifi er. Afterwards, you connect
the speaker cable to the upper and lower connector ter-
minators of the speakers respectively. Advantage: More
power and improved sound quality.
You only have to remove the
contact bridges for Bi-Wiring or
Bi-Amping operation:
To do so, turn the connector
terminals counterclockwise until
loose and then pull the contact
bridges out.
The top terminals lead to the high
range and midrange speakers,
the bottom terminals lead to the
low range speakers.
Connecting the cables
Danger
Danger of injury/damage!
Arrange the cables so that they do not pose a
trip hazard.
1. Turn off your amplifi er.
2. Lay the speaker cables from your amplifi er to each
speaker. These cables should be high-quality double-
wire speaker cable with marked strands. The diameter
should amount to at least 1.5 mm
2
.
Make sure that the polarity is correct!
Connect the same-colour terminals of your
speakers and amplifi er with each other. Oth-
erwise the sound quality will suffer. The individual single
wires of the speaker cables are marked with different
colours or shapes to facilitate the process.
3. Split the single
wire down to
approx. 30 mm
on both ends
and strip ap-
prox. 10 mm of
insulation off of
each cord. Twist
the stripped
single wire ends together so that no wire protrudes.
4. Turn the connector terminals
counterclockwise until loose.
Run the stripped single wire
ends into the holes that are
now visible. Turn the terminal
clockwise until closed.
The cable has now been
clamped in place.
5. Connect the other end of the
speaker cable to your amplifi er.
The operating instructions of
the appliance should contain
notes on this.
92135 GB 20120508.indd 692135 GB 20120508.indd 6 08.05.12 09:0508.05.12 09:05
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teufel Ultima 40 Mk 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teufel Ultima 40 Mk 2 in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info