686233
6
Zoom out
Zoom in
Previous page
1/8
Next page
6 T 500 F 16
CAUTION
Risk of injury/damage!
Lay the cables so that they do not pose a
tripping hazard.
Connection variations
In addition to normal connection where each
speaker column is connected to the amplifier/AV
receiver with a cable, you can also select the varia-
tions “bi-wiring” or “bi-amping” with the T 500 F 16
column speakers.
Normal connection
With this method, speakers are connected like
conventional speakers with one 2-strand speaker
cable each. The contact bridges between the
connector terminals must not be removed; you can
connect the speaker cables accordingly to the top or
bottom terminals.
Bi-wiring
With Bi-wiring, the speaker is connected to the
power amplifier/AV receiver via two separate
speaker cables for the low and medium-range
branch. Decoupling speaker systems this way can
improve the sound.
Bi-amping
Here, the low and the medium/high range branches
are supplied by an own power amplifier of the ampli-
fier/AV receiver each. Connect a speaker cable with
two strands to each power amplifier and connect
this cable with the upper or lower connector termi-
nals of the speakers. Advantage: Improved perfor-
mance and sound quality.
Connecting the cables
1. Turn off your amplifier/AV receiver.
2. Lay the speaker cables from your amplifier/AV
receiver to each of the speakers. Use a high-
quality double wire speaker cable with marked
strands for this.
3. A connector terminal with two or four pole termi-
nals is located on the back side of the speakers.
You can connect the speaker cables directly
here or using pin plugs. Direct connection only is
described here.
The terminals are marked in red (+) and black (-).
Connecting
NOTICE
Make sure the polarity is correct!
Connect each of the like coloured termi-
nals of your speakers and your amplifier/
AV receiver with one another; otherwise
the sound quality will suffer. To facilitate
this, the individual single wires of the
speaker cables are marked with different
colours or shapes.
4. Only remove the contact
bridges for bi-wiring
or bi-amping with the column
speakers:
To do this, loosen the
connector terminals by turning
them counterclockwise and
pull the contact bridges out.
The upper terminals lead to
the high and mid range
speakers and the bottom terminals lead to the
low range speakers.
5. Split the single wire down
by approx. 30 mm
on both ends and remove
approx. 10 mm of insulation
each. Twist the single wire
so that no strands are
protruding.
6. Turn the connector terminal
counterclockwise until loose.
Run the stripped cable end into
the now visible hole. Close the
terminal by turning it clock-
wise. The cable has now been
clamped in place.
7. Connect the other end of the
speaker cables to your amplifier/AV receiver. You
should be able to find corresponding notes in the
user manual of your device.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teufel T 500 F 16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teufel T 500 F 16 in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info