562469
3
Zoom out
Zoom in
Previous page
1/4
Next page
Preparation
Mounting the base plate
The base plate with spikes ensures a safe position of the
speaker, minimises vibrations and provides enough room for
routing the wires
.
You need a Phillips head screwdriver of size PH2 for assembly.
1. Lay the speaker with the back side on a soft, padded base
carefully (e.g. on the polystyrene pads from the packaging).
2. Place the base plate b on the speaker bottom carefully and
screw tighten it with 4 washers d and 4 screws c.
3. Screw the knurled nut f on the threads of the spikes e,
then screw the spikes into the threaded holes in the base
plate.
4. To compensate for uneven oors slightly unscrew the spikes
and x them with the knurled nuts.
5. In the event of soft or sensitive oors, place a washer g
under each spike.
6. Make sure that the speakers have a stable position to pre-
vent vibrations.
Setup and connection
Setup
Note
Our website contains comprehensive notes for correct setup.
Select a stable, level base.
Make sure that the environment is clean and free from dust.
Avoid placing the unit close to sources of heat or in direct
sunlight.
Arrange the connector cables so that they do not pose a trip
hazard.
Do not place any heavy objects on the cables or the spea-
kers.
Make sure that the speaker has a stable position to prevent
vibrations.
Connecting
Danger
Danger of injury/damage!
Arrange the cables so that they do not pose a
trip hazard.
Pull the power plug of your AV receiver or multi-channel ac-
tive subwoofer out of the socket.
Lay the speaker cables from your AV receiver or multi-
channel active subwoofer to each speaker. These cables
should be high-quality double-wire speaker cable with marked
strands. The cross section should amount to 1.5 to 4mm
2
.
A connector comprising two terminals is located on the
bottom of each speaker, to which you have to connect the
speaker cables.
The terminal clips are each marked red (+) and black (-).
Make sure the polarity is correct!
Connect the like coloured terminals. Otherwise the
sound quality will suffer.
The speaker connections of your AV receiver or
multi-channel
active subwoofer
should be marked similarly. The strands
of the speaker cables are marked with different colours or
shapes.
1. Split the single wire down to approx. 30 mm on both ends
and strip approx. 10 mm of insulation off of each cord.
2. Twist the stripped single wire ends together so that no wire
protrudes. Tin coating is not necessary.
3. Turn the connector terminal counterclockwise until loose.
Run the stripped cable end into the now visible hole. Close
the terminal by turning it counterclockwise. The cable has
now been clamped in place.
4. Connect the cables to the other speaker in the same way.
5. Connect the speaker cables to your AV receiver or multi-
channel active subwoofer. The operating instructions of the
appliance should contain notes on this.
Crossover frequency
The ideal separation frequency on the AV amplier or multi-
channel active subwoofer for the column speakers is 100 Hz.
b
e
f
d
c
4x
5x
5x
g
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teufel LT5 Mk2 FR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teufel LT5 Mk2 FR in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info