Manual Telwin FLASH START 700 (page 4 of 52) (All languages)

649702

Zoom out

Zoom in

1/52

- 4 -

than 3 seconds.

- If the car or boat does not start, wait until the starter

has charged completely (Green 14V LED ON), without

disconnecting the clamps from the battery, and try starting

the engine again.

After a successful start, with the engine running, follow the

sequence of instructions below with great care:

- Disconnect the black clamp (negative) from the vehicle.

- Disconnect the red clamp (positive) from the vehicle.

- Always store in a safe, dry place.

The starter does not need charging before storing it away.

4.2. Pre-charging methods

Sometimes, the vehicle battery is so low that it is unable to charge

the starter completely and the red “FAULT” LED comes on (g.

A-5).

In this case the starter must be charged using:

a. another car battery: connect the clamps to the battery poles and

press the “ON/OFF” button in gureA-3;

b. the 12V cigarette lighter socket of another vehicle;

c. a 5V / 2A mini USB port (g.A-8);

NB: the charging times depend on the system used and vary from

about one minute in case a- up to about twenty minutes in case

c- which is the slowest.

4.3Using thestarterWITHOUT thevehiclebattery (BYPASS

MODEgureB):

If the vehicle low battery charge system fails, it is always possible to

use a pre-charge method, as described in the previous paragraph,

following the exact sequence below:

- disconnect the positive terminal from the battery;

- connect the starter as seen in gure B-1;

- press and hold the “ON/OFF” button (g. A-3);

- the green LED in g.A-5 comes on;

- start the engine;

- connect the positive terminal to the battery together with the

starter positive clamp (g.B-2);

- only remove the starter clamps after tightening the battery

terminals.

- press the OFF button (g. A-3).

WARNING:

Never leave the engine running without rmly

fastening the battery connections.

In this way, the clamps remain energised for a few minutes:

press the OFF button as soon as the operation has been

completed,donotshort-circuittheclamps,donotinvertthe

polarity.

4.4Usingthe“GLOW”function

Diesel engines activate the “glow” function

to warm up the

combustion chambers to help ignition in cold weather conditions;

if the vehicle battery is too low, the engine chambers may not be

warmed up sufciently. In such a situation, when the starter is

completely charged, press the “GLOW” button (g.A-4), the LED

in g.A-5 comes on alternating between red and green. Start the

dashboard using the ignition key and wait for 4-6 seconds before

completing ignition with the key.

5.DISPOSAL

The user is obliged to dispose of this equipment as mixed municipal

solid waste, contacting an authorised collection centre. Contact the

local solid waste authority for information on recycling.

WARNING:

Do not burn the battery to dispose of it. This could cause an

explosion.

SPECIFICATIONS: FLASH START 700

Type of capacitors:

super capacitors

Equivalent capacity:

- 100F

Max output voltage:

- 15V

Starter current (12V):

- 400A

- (700A peak)

Starter cables:

- terminals with red and black clamps

- copper

- diameter 8.4mm

(8AWG)

- length 300mm

- PVC insulated

Input sockets:

- input charge socket with cable adaptor for 12V cigarette lighter

jack plug

- input charge socket for 5V - 2A mini USB

Characteristics:

- ON/OFF switch

- GLOW function

- output protection against polarity reversal and clamp short circuit

- automatic charging level reset switch

- charge level and fully charged indicator LEDs

- alarm indicator LED and special functions

Weight:

- 1.2 kg

Accessories included (g. A):

- Charger cable with cigarette lighter type 12V jack plug (g.A-6).

(IT)

MANUALE ISTRUZIONE

ATTENZIONE:

PRIMA DI UTILIZZARE L’AVVIATORE LEGGERE

ATTENTAMENTE IL MANUALE DI ISTRUZIONE!

1. SICUREZZA GENERALE PER L’USO DI QUESTO AVVIATORE

Allo scopo di ridurre il rischio di lesioni personali e di danni

all’attrezzatura, vi raccomandiamo di usare l’avviatore

rispettando sempre le fondamentali misure precauzionali

sulla sicurezza.

- Le persone inesperte devono essere opportunamente

istruite prima di utilizzare l’apparecchio.

- Ibambinidevonoesseresorvegliatipersincerarsichenon

giochino con l’apparecchio.

- Leggere attentamente e seguire le istruzioni del manuale del

veicolochesivuoleavviare:ilcostruttoredelveicolopuò

specicare quali forme diavviamentodi emergenza sono

ammesseequalisonodaevitare.

Proteggere gli occhi. Indossare sempre occhiali

protettivi quando si lavora con accumulatori al piombo

acido.

Evitare il contatto con l’acido della batteria. Nel caso si

venga investiti o si venga a contatto con l’acido,

risciacquare immediatamente la parte interessata con

acqua pulita. Continuare a risciacquare no all’arrivo del medico.

È importante collegare i cavi alle corrette polarità:

Collegare la pinza di carica di colore rosso al morsetto

positivo della batteria (simbolo +).

Collegare la pinza di carica di colore nero al telaio del veicolo

o al morsetto negativo della batteria, lontano dal condotto del

carburante.

- Usare l’avviatore in aree ben ventilate. Non tentare di

effettuare avviamenti quando ci si trova in mezzo a gas o

liquidi inammabili.

- Impedire alle pinze nere e rosse di venire in contatto.

- SOLO PER SISTEMI A 12 VOLT! Usare solo su veicoli con

sistemi elettrici a 12 volt.

- USARE SOLO IN CASO DI EMERGENZA. Usare esclusivamente

per effettuare l’avviamento.

- Evitare di lavorare da soli. Nel caso di incidente l’assistente può

prestare aiuto.

Evitare le scosse elettriche. Usare estrema cautela

nell’applicare le pinze a dei conduttori o barre di

distribuzione non isolati. Evitare il contatto corporeo

con superci quali tubi, radiatori e armadi metallici mentre si sta

misurando il valore di tensione della batteria del veicolo.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telwin FLASH START 700 in the language / languages: All languages as an attachment in your email.

The manual is 2,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telwin FLASH START 700 Manual

Product: