679709

Telekom Digitalisierungsbox Premium Manual

4
Zoom out
Zoom in
Previous page
1/4
Next page
For optimal WLAN performance attach both of the
supplied antennas to the device.
V. 2.0 - 20150223 - 5500001785
Info
LEDs
System requirements
Automatic configuration
ISDN connection
Select operating mode
Side view
Scope of supply
LEDs back view
1
Status Green
2
Service Yellow
The LEDs are linked to those on the top of the
device and show the identical behavior.
Mounting Brackets
Due to the position of the devices in a rack it is recommended to use remote antenna. Attach
the mounting brackets to the device using the supplied screws.
The mounting brackets and screws are available as an accessory (Part No. MN40285514).
During operation in a rack the ambient temperature must not exceed 40° C.
Software Update
Antenna connector
WLAN
First-time use of the Premium Digitalisierungsbox
Automatic configuration is a service for Telekom customers that you can use with your
Digitalisierungsbox.
Connect the Digitalisierungsbox to the mains. Connect the cables to the appropriate sockets/
jacks. Wait until the Service LED goes out.
Start an Internet browser, enter telekom.de in the address bar and confirm with the Return key.
You are redirected to the Telekom autoconfiguration page. Enter your access ID and your
password and click on Start Configuration. During automatic configuration, the Service LED
will light up.
Wait until a confirmation is displayed that the configuration has been successful. The Service
LED is no longer lit now.
If the Telekom webpage does not open, first check all cabling.
For the configuration of the device, the following system requirements must be met:
 Operating system Microsof
t Windows XP SP3 or later; Windows XP SP3 requires the following
hotfix: http://support.microsoft.com/kb/953761
 Internet Explorer version 7 or 9 or later (the security settings may need to be adjusted),
Mozilla Firefox version 4 or later, Chrome
 Installed network card (Ethernet)
 Installed TCP/IP protocol
 PC configured to automatically obtain IP address and DNS server
 High colour display (more than 256 colours) to show graphics accurately
Case 1: If the p
assword has not yet been changed, you can select the operating mode once
you log in.
Case 2: If the password has been changed, the device has been configured as a telephone
system ex works.
You can also change operating mode in the menu Assistants Ô First Steps Ô Operating
Mode. Note that some features will not then be available. Assembly and the basic configuration
are exactly the same.
If you switch from telephone system to media gateway or from media gateway to
telephone system, the device does a factory reset.
This means that the device reverts to condition it was in when it was supplied.
The configuration is deleted and all the passwords are reset.
Premium Digit
alisierungsbox
 One Ethernet LAN cable (yellow)
 One Ethernet WAN cable (blue)
 One DSL cable (black)
 Two connector cables analogue terminals (grey)
 Power supply unit
 Two Wi-Fi antennas
 Installation poster
 Safety instructions
The switches for terminating the ISDN interfaces can be found on the bottom / in the lower
housing. Both switches are set to ON ex works. This means that termination is enabled and
the device is preconfigured for the operation of all common applications.
The device is delivered with the system software version which is current at the time of
production. The system software is continually being upgraded to improve the security and
functionality of the device. When you first start the device, you may be prompted to update the
software. If you have access to Telekom's automatic configuration, the system software for
your device will automatically be updated to the latest version.
Alternatively, you can update the software in the User view. To use this option to update the
system, you require a functioning Internet connection.
Under Firmware Update, click Update to start the process.
Do not interrupt either the power supply or the internet connection.
Whenever new system software has been installed, you need to restart the device.
Should an error occur during the update process, do not restart the device and contact
customer service.
You can call the free numbers 0800 330 1300 or 0800 330 2870 (for corporate clients) during
normal business hours for any further advice on your Digit
alisierungsbox.
You can also find more information online at http://hilfe.telekom.de.
If you think your connection may be faulty, please call Technical Customer Service free
of charge at the respective number above, or refer to http://hilfe.telekom.de.
Please read the user guide before connecting the device or starting it up!
Reset
The reset is performed by using the reset button at the terminal area.
The device is rebooted by quickly pressing the key (ca. one second). Pressing the key is equivalent
to an interruption of the power supply. Saved data are preserved, but all connections are interrupted.
If you press the reset key for approx. 30 seconds, the device performs a factory reset. This means
the device is returned to its ex works state. Connection data for incoming and outgoing phone calls
are preserved. The configuration is deleted and all passwords are reset.
The reset has finished once the status LED flashes continuously again after approx. 30 seconds.
LED Colour Status Information
Service Yellow on Undergoing automatic maintenance
off No automatic maintenance
Mem. off Memory is ready for read/write accesses
Green flickering Read/write access
WLAN off WLAN or all assigned wireless networks disabled
Green slow Wireless network is enabled, no client is logged in
flashing
Green flashing Wireless network is enabled, at least one client is logged in
quickly
Green flickering Wireless network is enabled, at least one client is logged in,
there is some data traffic
DSL Green on Connection established
Green slow Synchronisation running
flashing
off No synchronisation
Green flickering Data transfer
TEL Green on Telephony ready at IP connector (Voice over IP)
off Telephony not configured
ISDN1/2 Green on ISDN telephone system connected
off On standby or not functioning
Status Green on After switching on: Device is started
While operating: Fault
Green slow The device is active
flashing
Power Green on The power supply is connected
off No power supply
ON
OFF
21
PowerStatusWLAN DSLMem. TEL ISDN1 ISDN2Service
Reset
1
2
DSL LAN1 LAN2 LAN3 LAN4 LAN5 ISDN1 ISDN2 a/b1 a/b2 a/b3 a/b4
Reset
1
2
LED Colour Status Information
LAN 1  4 (Link/Act) Green On Ethernet connection established
(Link/Act) Green Flashing Data transmission via Ethernet
(Link/Act) Off No Ethernet connection
(Speed) Green On 1000 Mbit/s transfer rate
(Speed) Orange On 100 Mbit/s transfer rate
(Speed) Off 10 Mbit/s transfer rate
LAN 5 (Link/Act) Green On WAN-Ethernet connection established
(Link/Act) Green Flashing Data transmission via ETH 5
(Link/Act) Off No Ethernet connection
(Speed) Green On 1000 Mbit/s transfer rate
(Speed) Orange On 100 Mbit/s transfer rate
(Speed) Off 10 Mbit/s transfer rate
The LEDs for the Ethernet sockets LAN-4 (LAN) and LAN5 (WAN) show the following status information:
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telekom Digitalisierungsbox Premium at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telekom Digitalisierungsbox Premium in the language / languages: German as an attachment in your email.

The manual is 7,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Telekom Digitalisierungsbox Premium

Telekom Digitalisierungsbox Premium Installation Guide - German - 114 pages

Telekom Digitalisierungsbox Premium Additional guide - German - 7 pages

Telekom Digitalisierungsbox Premium User Manual - German - 456 pages

Telekom Digitalisierungsbox Premium User Manual - German - 303 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info