336432
16
Zoom out
Zoom in
Previous page
1/22
Next page
GB
16
When the "safety disconnecting" has occu-
rred, in the corresponding plate's power
indicator the residual heat H indicator will
be displayed, if the glass temperature is
high enough.
SAFETY WHEN SENSORS ARE COVE-
RED
The Touch Control incorporates a function
that detects when any object (container,
cloth or certain liquids) are covering the
panel sensors for more than 10 seconds.
This is to avoid the object activating or
deactivating any of the plates without you
realizing.
When the Touch Control detects an object
covering the sensors, it starts to bleep until
the object covering the control panel is
removed. If the Touch Control was turned
on, it is automatically disconnected for
safety reasons.
If after a few minutes the object covering
the sensors is not removed, the bleeping
will stop.
Take into account that this safety
function is activated even though the
Touch Control is turned off!
Do not leave any objects down on
the Touch Control!
Clock
(except models …630)
The top is fitted with a clock that can be
used for two different functions: as a plate
timer or as a countdown chronometer.
The clock as a countdown timer
(except models …630)
With this function, you can set a time after
which a sound signal will be heard.
To activate this function, proceed as
follows:
1 With the Touch Control powered on and
no plate with the timer activated, touch
one of the sensors (11) or (12)
corresponding to the clock.
2 Power on the indicator (7), displaying
00.
3 Touch the sensors (11) or (12)
again to set the required time. After a
few seconds, the decimal point on clock
will start to blink (13), indicating that the
countdown has begun.
Be careful not to touch different sensors
other than (11) or (12) since, by
doing so, a plate may cease timing instead
of programming the chronometer.
Once the countdown has reached zero, a
series of bleeps will be heard. These can
be cancelled by touching any of the sen-
sors (11) or (12) associated with
Table 2
8
8
5
4
4
3
3
2
2
1
10 minutes
1
2
3
4
5
6
7
8
9
P
Power
selected
MAXIMUM
OPERATION TIME
(in hours)
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teka it 641 exp at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teka it 641 exp in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info