Manual Tecomec Compact 120V (page 6 of 32) (English, French, Spanish)

640526

Zoom out

Zoom in

1/32



 

- Loosen the knob M20.

- Turn the vise clockwise.

- Position the vise reference by the required angle.

- Tighten the knob again M20.

 

- Loosen the knob at the back M23 and turn the arm to the right.

Position the reference by the required angle.

- Tighten the knob again M23.

 

- Move the right cutter up against the chain blocking unit A29.

- Turn the knob P29 to position the blocking unit A29 correctly compared to the

cutter.

 

- Move the grinding wheel onto the right hand cutter, by pulling the arm

downwards.

- Turn the knob P30 to move the chain so that the cutting part of the cutter skims the

grinding wheel . The chain should run smoothly over the vise throughout

this procedure but without any clearance.

 

- Loosen the knob M20.

- Turn the vise anti-clockwise.

- Position the vise reference by the required angle.

- Tighten the knob again M20.

- Move the left cutter up against the chain blocking unit A29.

- Move the grinding wheel onto the left cutter, by pulling the arm downwards. The

grinding wheel must skim the left cutter by the same amount as the right cutter.

- If the difference is considerable, it means that the chain is not centred exactly

and you need to progressively and slightly turn the screw  until you nd the

correct position.

- Turn the vise onto the right cutter and check if it is centred again by lowering the

arm.

- The vise adjustment phase is complete once both cutters (right and left) are

perfectly centred with the vise rotation point.

 

It is obligatory to sharpen a chain with the gauge of the drive link identical to the

sample chain used in the previous vise adjustment phase.

 

- Once you have established the type of chain to be sharpened, look-up the adjust-

ment angles (vise and arm) in the chain chart (columns A/C).

RH CUTTER

 

- Loosen the knob M20.

- Turn the vise clockwise.

- Position the  reference mark on the vise by the desired

angle.

- Tighten knob M20 again.

LH CUTTER

 

- Loosen the knob M20.

- Turn the vise counter clockwise.

- Position the  reference mark on the vise by the desired

angle.

- Tighten knob M20 again.

 



- Loosen the knob at the back M23 and turn the arm towards the

right. Position the  reference mark by the angle desired.

- Tighten knob M23 again.

 

- Put the chain to be sharpened in the vise.

- Take the cutter up against the chain blocking device A29.

- Turn the knob P29 to position the blocking unit A29 correctly compared to the

cutter.

 

- Move the grinding wheel onto the cutter to be sharpened by pulling the arm

downwards.

- Turn the knob P30 to move the chain so that the cutter cutting edge skims the

grinding wheel . The chain should run freely over the vise throughout this

procedure but without any clearance.

- At this stage, raise the arm and screw the knob P30, to move the cutter to be

sharpened further forwards.





Blunter the cutters, greater must be this forward movement. Vice versa, for cutters

that are not too blunt, simply grind just a slight amount of material.

- Turn knob P31 to adjust the cutter sharpening depth. The grinding wheel should

skim the bottom of the cutter gullet.

- Once you have found the exact position of the cutter, tighten the chain blocking

handle M32.

 

- Wear personal protection equipment when sharpening.

- All adjustments must be made with the motor switched off and the grinding

wheel completely stopped.

- In the case of accidental impact or collision of the wheel during the sharp-

ening process, follow the instructions given in the “GRINDING WHEEL

WARNINGS” section.

- Clean the chain before sharpening it.

- To avoid overloading the motor excessively and to avoid damaging the chain cut-

ters, grind minimum quantities of material and do not stop along the same cutter

as this could burn the cutting edge.

- Do not use liquid coolants when sharpening.

 



 

- Make sure the vise blocking handle M32 is screwed tight and the chain is

blocked.

- Turn the machine on using switch I33 and sharpen the cutter by lowering the arm-

motor unit .

- Once you have sharpened the chain, raise the arm and loosen the handle M32.

- Run the chain forward to position the next cutter to be sharpened.

- Block again with the handle M32 and sharpen.

 

- Fit the 1/4” (6 mm) thick grinding wheel , following the instructions given in

points 13-17-18-19.

- Turn the vise so that the “0” reference mark is on position 0 .

- Turn the arm to take the “0” reference mark to 10°/15° .

- Position the dressing brick on the jaws and against the chain blocking unit

.

Hold the dressing brick rmly with one hand (being careful not to touch the

grinding wheel).

- Prole the grinding wheel by activating the machine and grind the grinding wheel

until you obtain a prole like the one illustrated in .

- Switch the machine off once you have nished.

 

- Remove the dressing brick and put the chain in the vise.

- Center the cutter compared to the grinding wheel by turning the knobs (P29 and

P30).

- Keeping the arm tilted, adjust the grinding depth on the gauge by turning knob P31

.

- Sharpen the gauge following the instructions given in the “SHARPENING” section.

For this type of sharpening procedure, there is no difference between the right and

left cutters, therefore sharpen all the gauges one after the other.

- Check if the depth gauge is correct, using the template with the shape related to

the type of chain used . Please also consult the chain table, column F.

 

 

Turn the machine off by turning the switch to position “0” and unplug the power cable

from the mains.

 

Once you have nished using the machine, disconnect it and clean it thoroughly.

Store it in a dry and safe place, protected against dust and damp.

 

Follow the instructions given in the “STOPPING” section before you start to

work on the machine.

 

When the grinding wheel reaches a

minimum diameter of approximately

105 mm

Replace the grinding wheel.

40 hours

Clean the grinder carefully using a rag or

a cleaning brush.

Clean the electric motor and the sliding

guides with caution.

Do not use compressed air.



P00801077_R03_COMPACT_U&M_120V.indd 4 12/12/2012 14.33.45

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tecomec Compact 120V in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tecomec Compact 120V Manual

Product: