622564
1
Zoom out
Zoom in
Previous page
1/2
Next page
Istr-trony-6 cod-eng GMT S2 Pag. 1
di 2
INSTRUCTION HANDBOOK FOR
ELECTRONIC DOUBLE CODE SAFES
Please read all of these instructions carefully before commencing using your
safe. Try all of these procedures with the door open first, until you are familiar with how the safe works
1. FEATURES
High performance microprocessor.
ALKALINE BATTERY inner feeding.
12 key membrane keyboard: 10 keys with 0 to 9 figures. 4 dedicated led and contacts for external emergency feeding in
case of exhausted inner battery.
ON” key to activate the circuit.
ENTERkey to confirm code set and consent to the opening.
Internal programming key for a new personal code (in some models it is protected with a sliding cover).
TWO PERSONAL OPENING CODES WHICH CAN BE SET UP.
DIGITS THAT CAN BE SET: minimum 6 maximum 10. (the “ENTER” and “ON” keys are not valid in the
combination).
2. INTRODUCTION
ALL SAFES ARE PROVIDED WITH SERVICE CODE “1 1 1 1 1 1”.
THE SAFE OFFERS TWO CODE TO BE SET UP, WE ADVISE TO USE BOTH OF THEM TO AVOID
FORGETTING THEM.
Before installing the safe, check that it works properly and read the instructions carefully to understand the operation.
Every time a key is pressed the green “OK” LED lights up and the buzzer sounds; pressing the “ENTER” key causes the
green “OK” LED to light up for correct procedures, or the red “ERROR” LED to light up in the case of incorrect settings.
3. FIRST APPLICATION
Alimentation:
Unscrew the cover screw and put the batteries, of the type stated on the label, into the proper case on the rear of the lock
(see picture 1) - Screw again the cover screw.
Use only and exclusively alkaline batteries.
Safety block removal:
remove completely (without screwing it any longer) the blocking black screw, blocking the magnet, which is marked by a
proper yellow tag.
WARNING!
To screw the black screw after removing it compromises the safe operation.
Test for opening using the service code “1 1 1 1 1 1” (with door open and bolts extended):
1. Press “ON”, key in the service code 111111and press ENTER”. The green “OK” LED lights up for about five
seconds.
2. Within this time, with the green LED “ON”, turn the knob clockwise to retract the bolts. If the combination is incorrect,
the red “ERROR” LED will light up and the buzzer will sound. After three attempts with incorrect codes, the keyboard
will be disabled for one minute and this time will be indicated by the red “ERRORLED flashing. After this time,
renewed readiness for operation will be indicated by the green OK” LED lighting up and a beep.
4. STORING THE PERSONAL CODE:
1. With the door open and the bolts outside, press the “ON” key and, after that, the “PROGRAMMING” key place on the
inside side of the door ( see Picture 1). The “CODE” green LED lights up with a fixed light for about 10 seconds.
2. Within 10 seconds, start keying in your new personal code (min. 6 – max. 10 digits) and press “ENTER”.
3. Start keying to confirm your personal code and to press the key "Enter."
If you do not want to program the second code, wait some seconds and a multiple tone signal shall confirm that
your personal code has been stored.
In order to store a second code, go on with following procedure at the end of item 3 within 3 seconds:
4. Press the " PROGRAMMING Key"
5. Start keying to second personal code from 6 to 10 figures and to press the key "Enter."
6. Start keying to confirm your second personal code and to press the key "Enter."
A multiple tone signal shall confirm that your codes have been stored.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technomax SMT vanaf 2009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technomax SMT vanaf 2009 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technomax SMT vanaf 2009

Technomax SMT vanaf 2009 User Manual - Dutch - 2 pages

Technomax SMT vanaf 2009 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info