542240
9
Zoom out
Zoom in
Previous page
1/10
Next page
6
9
battery door and insert 3 x AA batteries into the battery
compartment. Make sure you insert the batteries the
right way according to the polarity information marked
on the battery compartment.
2. Replace the battery door.
3. Press the “RESET” key to re-start the clock and it will
synchronize the channels of transmitter automatically.
NOTE:
1. The building material and the position of the receiver
and transmitter affect the effective range. So try various
locations to obtain the best result.
2. Place the units away from metal objects and electrical
appliances to minimize the interference. Position the
receiver and transmitter within the effective
transmission range: 80m in usual circumstances.
RECEPTION OF RADIO CONTROLLED TIME SIGNAL
The time and date are radio-controlled. The current time
and date are automatically synchronized with the time
signal transmitted from Germany (DCF 77)/U.K. (MSF)/
USA(WWVB).
When used for the first time (after inserting the batteries or
pressing the “RESET” key), the clock will start to receive the
RC signal in 5 minutes with the signal strength indicator
flashing.
5. Press “TIME” key to save and exit the setting or let it exit
automatically 30 seconds later without pressing any key.
ALARM AND SNOOZE SETTING
1. In normal time mode, press “TIME” key to select the
ALM1 or ALM2.
2. In ALM1/ALM2 mode, press and hold “ALARM” key for
2 seconds until alarm Hour digit flashes.
3. Press “UP” or “DOWN” key to change the value.
4. Repeat the above operations to set time in this order:
Hour > Minute
5. Press “ALARM” key to save and exit the setting, or let it
exit automatically 30 seconds later without pressing
any key.
NOTE:
1. The alarm will be automatically turned on when you
set the alarm time with the icon ” or displayed.
2. The dual-alarm (ALM1&ALM2) design of this unit will
provide you with more convenience, and you can set
two-alarm time if needed.
USING ALARM & TEMPERATURE PRE-ALARM FUNCTIONS
1. Set the alarm time as described in the previous section.
2. In normal time mode,press “ALARM ” key once to turn
on ALM1, press it twice to turn on ALM2, press it thrice
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Techno line WT 529 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Techno line WT 529 in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info