542197
3
Zoom out
Zoom in
Previous page
1/16
Next page
21
at start-up. This code must be received and stored by the Weather Station in the first 3
minutes of power being supplied to the transmitter.
BATTERY CHANGE:
It is recommended to replace the batteries in all units on an annual basis to ensure optimum
accuracy of these units.
Please participate in the preservation of the environment. Return used
batteries to an authorized depot.
SETTING UP
WHEN ONE TRANSMITTER IS USED
1. First, insert the batteries in the transmitter (see “How to install and replace batteries
in the Termo-hygro outdoor transmitter above).
2. Within 2 minutes of powering up the transmitter, insert the batteries in the Temperature
Station (seeHow to install and replace batteries in the Weather Station above).
Once the batteries are in place, all segments of the LCD will light up briefly and a short
signal tone will sound. Following the indoor temperature/humidity and the time as 0:00
will be displayed. If these information are not displayed on the LCD after 60 seconds,
remove the batteries and wait for at least 60 seconds before reinserting them. Once
the indoor data is displayed user may proceed to the next step.
3. After the batteries are inserted, the Weather station will start receiving data signal from
the transmitter. The outdoor temperature and humidity data should then be displayed
on the Weather station. If this does not happen after 2 minutes, the batteries will need
to be removed from both units and reset from step 1.
4. In order to ensure sufficient 868 MHz transmission however, the distance between the
Weather Station and the transmitter should not be more than 100 meters (see notes on
Positioning” and “868 MHz Reception”).
Note:
In the event of changing batteries of the units, ensure the batteries do not spring free from
the contacts. Always wait at least 1 minute after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
WHEN MORE THAN ONE TRANSMITTER IS USED
1. User shall remove all the batteries from the Weather Station and transmitters, and wait
60 seconds.
2. Insert the batteries in the first transmitter.
3. Within 2 minutes of powering up the first transmitter, insert the batteries in the Weather
Station. Once the batteries are in place, all segments of the LCD will light up briefly
and a short signal tine will sound. Following the indoor temperature/humidity and the
time as 0:00 will be displayed. If these information are not displayed on the LCD after
60 seconds, remove the batteries from both units and wait for at least 60 seconds
before reinserting them.
4. The outdoor temperature and humidity data from the first transmitter (channel 1)
should then be displayed on the Weather Station. Also, the signal reception icon will be
displayed. If this does not happen after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.
5. Insert the batteries in the second transmitter as soon as the outdoor temperature and
humidity readings from the first transmitter are displayed on the Weather Station.
Note :
User shall insert the batteries into the second transmitter within 45 seconds
after the Weather Station displays the information of the first transmitter.
6. The outdoor temperature and humidity from the second transmitter and the "channel 2"
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Techno line WS 9032 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Techno line WS 9032 in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Techno line WS 9032

Techno line WS 9032 User Manual - German - 8 pages

Techno line WS 9032 User Manual - Dutch - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info