658284

TC Helicon Mic Mechanic 2 Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
4 MIC MECHANIC 2 User Manual
Connection
• Connect a microphone to the MIC jack
• Connect the OUT jack to a mixer, interface or active speaker
• Connect the power cable (optional)
• Connect a micro USB cable to a computer (optional)
Tap Tempo
The echo tempo can be manually adjusted to match the song you’re performing.
Simply hold the Footswitch down for about 2 seconds to enter Tap Mode. The
on/o LED will  ash in rhythm with the current tempo. Tap the footswitch a few
times in rhythm with your desired tempo, and on the last tap, hold your foot on
the switch for around 2 seconds to exit Tap Mode.
Note – the pedal will not “time out” of Tap Mode, so you can keep this mode
active if you intend to leave the e ect on throughout a song or set, allowing you
easier access to this function.
Adjusting Echo Feedback
Feedback is the parameter that controls how many repeats are heard in the
echo e ect. By holding the Tone button and turning the Correction knob, you
can adjust the feedback length. As soon as you release the Tone button, the
Correction knob will resume its normal function.
Changing the Batteries
The Mic Mechanic 2 can operate on 4 AA batteries. Remove the single screw on
the bottom of the pedal to open the battery door. Make sure to observe correct
polarity when inserting the batteries.
Auto Gain
Mic Mechanic 2 will automatically adjust the gain setting for your microphone,
eliminating the need for manual adjustments and ensuring that a good signal is
passed to the mixer without any unwanted distortion.
24V Phantom Power
Phantom power is always active on the Mic Mechanic 2. This will power
condenser microphones, but will not a ect dynamic mics either.
Mic Control
Mic Control allows you to control the e ect's on/o status via an MP-75
microphone. Press and hold the footswitch while powering up the unit to
toggle Mic Control.
Note that when using a condenser microphone, Mic Control should be disabled
to prevent unwanted on/o switching.
Micro USB cable
MP-75 microphone
Mixing board
Power cable
2. Operation
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for TC Helicon Mic Mechanic 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of TC Helicon Mic Mechanic 2 in the language / languages: English as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info